Larry posted an answer for this Welding Tools:
"WTF is a "tipo" ? YES your machine is defective."
Larry posted an answer for this Welding Tools:
"Most likely HF spark adjustment needs to be done."
Larry posted an answer for this Welding Tools:
"Not enough information to answer. Is it plugged in? :)"
Larry posted an answer for this Welding Tools:
"Could be as simple as having the ground cable connection placed into the wrong port on the..."
Larry posted an answer for this Welding Tools:
"HF spark gap adjustment needs to be done, it's inside the machine, front of bottom circuit..."
Larry posted an answer for this A & A Manufacturing Ramsond Cut 50 Dx A 50a Amp Amp Inverter Plasma Cutter:
"Question is too general, what exactly are you asking?"
Larry posted an answer for this A & A Manufacturing Ramsond Cut 50 Dx A 50a Amp Amp Inverter Plasma Cutter:
"need wiring help on new plasma cutter"
Larry posted an answer for this Inverter Welding Tools:
"Internal componet failure, return the machine for repair. Who did you purchase it from?"
Larry posted an answer for this Inverter Welding Tools:
"I have a cheap chinese inverta plasma cutter ,a giant cut 40. When i press the trigger the..."
Larry posted an answer for this A & A Manufacturing Ramsond 40D Plasma Cutter Inverter:
"Does the cooling fan come on?"
Larry posted an answer for this A & A Manufacturing Ramsond 40D Plasma Cutter Inverter:
"i was using drop cord may have been to small to carry the loadit wasnt performing right it..."
Larry posted an answer for this A & A Manufacturing Ramsond Cut 50 Dx A 50a Amp Amp Inverter Plasma Cutter:
"What is the probelm with your machine?"
Larry posted an answer for this A & A Manufacturing Ramsond Cut 50 Dx A 50a Amp Amp Inverter Plasma Cutter:
"do you have a wireing diagram for a cut 50 lower boards /"
Larry posted an answer for this Inverter Industry Cut40d 40 Amps Amp Plasma Cutter:
"I need the main power resistors. RX24N. 50 watt, 18 ohm resistors, where can i get 4 of..."
Larry posted an answer for this Inverter Industry Cut40d 40 Amps Amp Plasma Cutter:
"How do you knwo they are bad?"
Larry posted an answer for this A & A Manufacturing Ramsond 40D Plasma Cutter Inverter:
"I have a Cut 40 Plasma cutter. The air turns on but the arc does not start . The internal..."
Larry posted an answer for this A & A Manufacturing Ramsond 40D Plasma Cutter Inverter:
"Check your consumbales to be sure they are tight in the torch head. Check your ground be..."
Larry posted an answer for this A & A Manufacturing Ramsond 40D Plasma Cutter Inverter:
"I have a chinese made (generic) 3-1 machine(plas,tig mma) .It has run for about 10 minutes..."
Larry posted an answer for this A & A Manufacturing Ramsond 40D Plasma Cutter Inverter:
"You are from Austrialia yes? If you'll email me at [email protected] I..."
Larry posted an answer for this A & A Manufacturing Ramsond 40D Plasma Cutter Inverter:
"'Who is the manufacture for lotos cut50. I wanted to buy consumables for the torch but..."
Larry posted an answer for this Welding Tools:
"Common problem with the SUPER series of Chinese machines. If you can provide some photos..."
Larry posted an answer for this Welding Tools:
"We sell the 3 in 1 machines. GiantTech CT520D , we've have very good luck with them with..."
Larry posted an answer for this A & A Manufacturing Ramsond 40D Plasma Cutter Inverter:
"Test all the mosfets, good chance one or more are failed."
Larry posted an answer for this Welding Tools:
"When you press the torch trigger what sound/sounds do you hear from within the machine?"
Larry posted an answer for this Inverter Welding Tools:
"Explain more please?"
Larry posted an answer for this RTO Esab Handy Plasma 550 W/25' Pt 31XL Torch 0558002612:
"Be sure you have the ground is connected to the postive terminal on the bottom of the..."
Larry posted an answer for this Welding Tools:
"Ha?"
Larry posted an answer for this Hobart Welders Champion 500433A Factory Reconditioned 10,000 Watt Generator:
"Hi, remove the machines cover with the machine unplugged then look for disconencted plugs..."
Larry posted an answer for this Inverter 50a Amp Plasma Cutter, Air , Cut50d 110/220vac:
"You need to check the internal connections coming from the panel switch connections..."