Knows a lot of useless information that can become useful depending on your circumstances
Chris C posted an answer for this Kitchen Ranges:
"What is the make and model? EG on a whirlpool oven its F1 - Control Board Failure -..."
Chris C posted an answer for this Whirlpool Ovens:
"F2 - Oven Temperature Is Too High - Check for welded contacts on bake and broil relays. If..."
Chris C posted an answer for this Miscellaneous:
"An answer from a doctor: http://www.texasheart.org/HIC/HeartDoctor/answer_1926.cfm"
Chris C posted an answer for this Cars & Trucks:
"Check for breakages or shorting in wiring"
Chris C posted an answer for this Frigidaire Kitchen Ranges:
"F3 - Open/shorted sensor (RTD probe) connection. Check the temperature sensor and the..."
Chris C posted an answer for this Cars & Trucks:
"Put a meter across the terminals the red is positive the black neutral if you get a..."
Chris C posted an answer for this 2000 Honda Odyssey:
"Check fuel level, fuel pump and spark from spark plugs"
Chris C posted an answer for this Nissan Cars & Trucks:
"The wires are the screen heater for clearing a fogged up rear screen. Removal would mean..."
Chris C posted an answer for this Washing Machines:
"Check filter Check pump isn't blocked with fluff"
Chris C posted an answer for this Dewalt Garden:
"Check spark plug is getting a spark and spark plug electrode gap"
Chris C posted an answer for this Office Equipment & Supplies:
"200 Sq Ft = 18.58 sq Mtrs"
Chris C posted an answer for this Washing Machines:
"Is it making a pumping sound when it should be? If so the pump could be blocked with food..."
Chris C posted an answer for this Hyundai Cars & Trucks:
"Could be a no of things: Overheating fuel pump relays. Overheating ignition coils"
Chris C posted an answer for this Cars & Trucks:
"Fault codes - Condition code and communication code descriptions - ELECTROLUX -KELVINATOR..."
Chris C posted an answer for this Audio Players & Recorders:
"When I Consider - Matt Gilman"
Chris C posted an answer for this Heating & Cooling:
"Sounds like the gas jets are clogged clean the jets with acetone but make sure the unit is..."
Chris C posted an answer for this Office Equipment & Supplies:
"Assuming you have ink, you need to clean and/or realign the print heads. Go to properties..."
Chris C posted an answer for this Cars & Trucks:
"Remove the trim at the bottom of the wheel arch and you should see a retaining screw or..."
Chris C posted an answer for this Washing Machines:
"You haven't given a make or model no. and Not know ing your location I can't advise on a..."
Chris C posted an answer for this Washing Machines:
"fault indicates that there was an instantaneous current spike at the motor windings in the..."
Chris C posted an answer for this Maytag Bravos MVWB400V Washer:
"Check outlet filter is clear and hose aren't kinked"
Chris C posted an answer for this Washing Machines:
"Check power supply"
Chris C posted an answer for this Bosch Washing Machines:
"Sounds like the filter is blocked or a exhaust hose is kinked"
Chris C posted an answer for this Maytag Bravos MTW6600T Top Load Washer:
"Later level pressure switch is faulty"
Chris C posted an answer for this Bosch Washing Machines:
"F21 refers to the carbon brushes in the motor so price new brushes - if you are handy they..."
Chris C posted an answer for this Washing Machines:
"4e is normally a water supply error - ensure water is reaching the inlet"
Chris C posted an answer for this Whirlpool Calypso GVW9959K Top Load Washer:
"Normally a simple fix: Tip the washer back at a 45 degree angle. On the bottom panel there..."
Chris C posted an answer for this Washing Machines:
"Are you sure 860 is the error and not the model no? Here are the common Hotpoint error..."
Chris C posted an answer for this Home Comfort HCWP1201 1.7 cu. ft. Portable Washing Machine With 12 lb:
"Inlet Solenoid is faulty - very common problem"
Chris C posted an answer for this Washing Machines:
"Wrong size belt - or fitted with tensioner that needs adjustment"
Chris C posted an answer for this Samsung Washing Machines:
"Unplug - take top and or back panel off - support weight of the drum - remove old belt -..."