Ned White posted an answer for this 2000 Ford Focus:
"I do not know the exact torque, but your dealer does, it is critical. Too loose is better..."
Ned White posted an answer for this 1990 Lincoln Town Car:
"No, not likely, freeze plugs are down on the sides of the engine, big, 1 1/4 dia plugs. If..."
Ned White posted an answer for this Cars & Trucks:
"250 is not low, it is just about to boil over, coolant boils at 260 in a closed system,..."
Ned White posted an answer for this Umarex Air Ruger Air Hawk Air Rifle .177 Cal:
"well for starters, there is no firing pin, second, without major machinery, you can't..."
Ned White posted an answer for this 1999 Dodge Ram 2500 4WD:
"why>?? The heads can be resurfaced and the valves ground, no need to replace the heads."
Ned White posted an answer for this GMC Cars & Trucks:
"It might be a freeze plug, but I bet it is an O-ring on a pipe back there under the..."
Ned White posted an answer for this 1991 Mercedes-Benz 420:
"Probably has 3 or 4 of them in the exhaust from the header down past the catalytic..."
Ned White posted an answer for this KONUSPRO 4X32 MBLK KON7262:
"Are you trying to see the reticule move? Or are you shooting after moving the adj..."
Ned White posted an answer for this Cars & Trucks:
"You mean the bendix drive is getting hung up on the ring gear??? Oh boy, I have seen this..."
Ned White posted an answer for this 1999 Dodge Grand Caravan:
"Most cars will go their liftime without a problem from wheel bearings. And they let you..."
Ned White posted an answer for this Office Equipment & Supplies:
"Most small motors are 12 volt, but they do vary. If your transformer melted down, There is..."
Ned White posted an answer for this Motorcycles:
"Make sure it is not in gear, kill switch off, kickstand up or switch working. Check the..."
Ned White posted an answer for this 2000 kawasaki VN 800 Vulcan Classic:
"Sit at a traffic light till the temp reaches about 220, it should start about then. My fan..."
Ned White posted an answer for this Craftsman 20 hp 42 in. Deck Lawn Tractor - CA Model:
"2 things, one, the belt jumped track, broke, or melted in place, 2, the hydrostatic ******..."
Ned White posted an answer for this Cars & Trucks:
"Dirty terminals, seen it a hundred times. They have to be squeaky clean. Check it out."
Ned White posted an answer for this Yamaha Motorcycles:
"One of those wires is potentially for the light bulb inside the tach. Find that one first...."
Ned White posted an answer for this 2003 Suzuki GZ 125 Marauder:
"Only one way to find out, get the bike running in the driveway with a couple spotters with..."
Ned White posted an answer for this Motorcycles:
"THe alternator is not charging. I would check the wires on the left side gong into the..."
Ned White posted an answer for this 1999 Dodge Intrepid:
"THe heat and air has nothing to do with the exhaust, It is either burning rich, burn your..."
Ned White posted an answer for this Nikon D70 Body Only Digital Camera:
"Won't take a picture?? Why not?? Chip in? battery up? Any error readings? Lens in..."
Ned White posted an answer for this 1999 Oldsmobile Cutlass:
"No, It depends on the car, I am not familiar with the engine in your olds, is it a belt or..."
Ned White posted an answer for this Water Heaters:
"LP or natural? Got gas? Is there anything in the house gas? Stove, etc? Age of heater? The..."
Ned White posted an answer for this Craftsman 20 gal Horizontal Compressor:
"Mine will not start unless the tank is empty, or when it is cold out. I need a min of 20..."
Ned White posted an answer for this Delta Masonry Tools:
"The most important part of the jointer is that the cutting edge is perfectly level with..."
Ned White posted an answer for this GE Profile 36" Electric Induction Cooktop - Black:
"You have lost half of the circuit in the breaker, the lights work on one side of it but..."
Ned White posted an answer for this Delta Saws:
"How hard is it to turn by hand? Anything binding? The starter windings can be replaced in..."
Ned White posted an answer for this Craftsman 12 Inch Band Sawsander I2 X80 Inch 100 Grit:
"Yes, glue them on with contact cement."
Ned White posted an answer for this Sears Saws:
"Paint the tire and the wheel with contact cement and let it set till you can touch it..."