will fix anything with a plug
Denny Adams posted an answer for this Dyson DC14 Animal Bagless Upright Cyclonic Vacuum:
"Cheap plastic parts. trade it in on a good vacuum like panasonic"
Denny Adams posted an answer for this Hoover SteamVac F5914-900 SpinScrub Upright Vacuum:
"dried soap in tubing. clean them out"
Denny Adams posted an answer for this Electrolux Vacuums:
"check hose for clogs"
Denny Adams posted an answer for this Shop Vac Vacuums:
"hot plastic. the motor bearings are bad"
Denny Adams posted an answer for this Kenmore Vacuums:
"sears parts on line"
Denny Adams posted an answer for this Rainbow Vacuums:
"Relace them"
Denny Adams posted an answer for this Dyson Vacuums:
"get rid of it. Dyson is a piece of junk from the gitgo. over 20 years in the vac repair..."
Denny Adams posted an answer for this Hoover Vacuums:
"replace the belt, or the roller may be frozen"
Denny Adams posted an answer for this Ridgid 40128 WD1680EX 16 Gallon Wet/Dry Vac With Detachable:
"No more than any other vac"
Denny Adams posted an answer for this Oreck XL Shield Power Scrubber Floor And Carpet Cleaner:
"Oreck is junk, despite the ads. trade it in on a Royal and yuu problems are over. been in..."
Denny Adams posted an answer for this Oreck XL Shield Power Scrubber Floor And Carpet Cleaner:
"this is a piece of junk. trade it in on a royal"
Denny Adams posted an answer for this Hoover Vacuums:
"replace the pulley"
Denny Adams posted an answer for this Miele Vacuums:
"could be as simple as a broken belt or a clogged hose run a broomhandle through it or a..."
Denny Adams posted an answer for this Bissell Powerforce 13" Brushroll 6582 6583 3530 3537 46E5 71Y7:
"there is likely a broken cam inside.replace it"
Denny Adams posted an answer for this KitchenAid K45SS Classic Stand Mixer:
"take off the chrome ring around the rotator. remove the screws that were hiding under it...."
Denny Adams posted an answer for this KitchenAid KSM90 Ultra Power Series Stand Mixer:
"kitchenaid parts on line, try mixing smaller batches of dough"
Denny Adams posted an answer for this Dyson DC07 Bagless Upright Cyclonic Vacuum:
"its a dyson......get rid of it"
Denny Adams posted an answer for this Singer Vacuums:
"try cleaning the ends of the brush roller. thread gets caught in there and jams it"
Denny Adams posted an answer for this Dirt Devil M085805 Upright Vacuum:
"likely the belt is crooked, and jammed in the floor plate. try reseating it."
Denny Adams posted an answer for this Kenmore Vacuums:
"most likely your bearings are shot. it will need a new motor"
Denny Adams posted an answer for this Oreck XL21 Bagged Upright Vacuum:
"you probably have a broken belt. replace it"
Denny Adams posted an answer for this Euro-Pro EP055 Bagged Canister Vacuum:
"find a sew and vac store in your yellow pages"
Denny Adams posted an answer for this Hoover Vacuums:
"this is a left handed thread you mite have to hold the other end of the shaft twith a pair..."
Denny Adams posted an answer for this Kenmore 34720 Upright Vacuum:
"sounds like one of two problems 1 it may not be seated properl2 the bearings in the motor..."
Denny Adams posted an answer for this Eureka Altima Upright Vacuum Model 2996AVS Vacuum:
"it slides in to a channel on the top of the bag compartment"
Denny Adams posted an answer for this Kenmore 22812 Bagged Canister Vacuum:
"likely a belt or broken wire in the power head"
Denny Adams posted an answer for this Miele Vacuums:
"find a vac repair shop in your area or google VDTA and they can direct you"
Denny Adams posted an answer for this Hayden Industries SuperVac 6000 Central System Vacuum:
"one of two problems cause this. first is a short in the wires that turn it on, the small..."