Whirlpool Washing Machines - Page 8 - Recent Questions, Troubleshooting & Support


how does the World Pool AWG 5070 operates to wash?

Whirlpool... | Answered on Jun 21, 2019


Hi mrcooperdog,
The diagnostics for a front loader is pretty simple. I have enclosed a link to a similar machine.
Watch it carefully and do it afterwards.
Good luck!
JP https://youtu.be/CFuosqBhfRc

Whirlpool Duet... | Answered on Jun 21, 2019


https://youtu.be/3OfwNr0e9ao
F6 error code for this model indicates a drive motor tachometer error. The control board is unable to properly detect the motor speed. If you have a volt/ohm meter I can give you a few checks that will help you diagnose the problem. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. You will need to gain access to the MCU (Motor Control Unit), and measure the motor windings . MCU connection should be as it is in your washer, there should be 5 black wires and 1 green wire. The black wires are as follows, pin 1 on top and pin 5 on the bottom . Set your meter to read resistance and check pin 1 to pin 2, pin 1 to pin 3, and pin 2 to pin 3, these should all read approximately 5 io 6 ohms. Next check pin 4 to pin 5, it should read approximately 115 to 125 ohms. If any of these readings are not very close to the values I have given you, check continuity on the wires from the MCU to the drive motor. If the wires check good, the drive motor is bad and will need to be replaced. If all readings are close to the values I gave and there is not an issue with the wires the MCU will need to be replaced.

Before doing anything else, try this fist :
Another Tech has discovered that by just unhooking the the 2 green ground wires at the motor, the washer runs just fine- the tub, body and the rest of the machine is still grounded.

Whirlpool... | Answered on Jun 16, 2019


If the machine keeps filling with the power off, it will mean the water valve (s) are faulty. If it only overfills when using the machine, it has to be in the pressure system. Check that the bell (where the bottom of the air tube fits on the tub) is not blocked and that there are no kinks or damage to the tube. The machine has to be empty when changing any part of the pressure system or it will flood again.

Whirlpool... | Answered on Jun 16, 2019


that number is a part number of the owners manual, if it's a front loader you have to remove the top lid, after you unplug machine of coarse, then reach down from the top down the front right side of the door and find a tab to either push or pull to release door. the lever will be at the door lock behind the front panel

Whirlpool... | Answered on Jun 14, 2019


run a couple of rinse cycles

Whirlpool... | Answered on Jun 13, 2019


Unbalanced load. Some washing machines are more susceptible than others.

Whirlpool... | Answered on Jun 13, 2019


Request directly from Whirlpool or a Whirlpool dealer

Whirlpool... | Answered on Jun 10, 2019


sorry there right ..your not using he or low suddsing detergent ,or your using to much..as the water pumps out of unit the sudds stick to side of tub than when rinse water comes in it washes back on your clothes...i can only give you tips and something to look for...look for water not drainning fast enough ,,cut down on detergent,,wash your dark clothes first..give your unit a bleach clean about a pint of bleach..keep me posted onthejob

Whirlpool Cabrio... | Answered on Jun 09, 2019


Two things to check and try although I'm not a washer repair man or know anything about certain models. >> 1-- To make the job a bit easier find a block of wood like a 2x4 or a 4x4, tilt the washer back and set the front of the washer up on the block or blocks.

Now take off the bottom front panel of the washer. There are a couple of screws at the very bottom that need to be removed. Then tap on the panel while pulling down and it will slide right off.

On the right hand side reach up inside the front panel to the latch assembly. Grab hold of the tab on the bottom of the latch assembly and your door will open.

If your door keeps getting stuck then you may need to replace the door latch assembly.

#2 ---1.Unplug machine
2.remove bottom panel
3.Reach up along the inside of the front panel and locate the bottom of the door latch assembly
4.Located on the bottom of the door latch assembly is a tear dropped shaped tab
5. Gently pull down on the tab about a 1/4 inch or until a click is heard.
.

Whirlpool... | Answered on Jun 07, 2019

Not finding what you are looking for?
Whirlpool Logo

Family Lines

33,300 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...