Whirlpool Washing Machines - Page 4 - Recent Questions, Troubleshooting & Support

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.Jun 13, 2019

Error Codes in Front Load Washers - Whirlpool Home Appliances

https://producthelp.whirlpool.com > Washers > Washer_Product_AssistanceSearch for: How do I clear the error code on my Whirlpool washer?

Whirlpool... | Answered on Oct 12, 2019

remove 2 screws on rear of console lift console forward and roll back remove the lid switch connector remove the 2 clips on each side pull rear of cabinet forwardand slide cabinet off remove screws in center of agitator under cap and pull off ..lean washer backward remove pump clips and hoses remove 2 screws in motor clamps remove clamps and motor remove 3 1/2 in bolts holding gearcase to bottom slide gearcase out remove clutch and reinstall on new gearcase if you go slow and take note reassembly not that hard

Whirlpool... | Answered on Oct 08, 2019

sounds like the motor or clutch pack is bad if so its a expensive fix

Whirlpool... | Answered on Oct 05, 2019

Unplug washer for 30 minutes. Plug back in se if opens. If not take off top panel off washer. There is a latch to release door.

Whirlpool... | Answered on Oct 03, 2019

i had the same problem. take the bottom cover off of the front of the washer. on the right you will see a round white screw off cover, it is very tight, it unscrews counter clock-wise. pull this out and see if there is any debris in it. if you look into the hole on the right side there is a hole about 1 inch round, this is the pump opening. you may have to take the gray drain hose off of the back of the pump housing and feel if anything is stuck in there, in my case there was a penny stuck side ways blocking the flow of water. after i took it out the washer has been running great again. this is obviously a design flaw, that something that large could manage to get that far, lucky for me it didn't damage the pump impeller. hope this helps. this should take care of the SD and the F21 error codes.

Whirlpool Duet... | Answered on Sep 29, 2019

the drain hose may be kinked therefore restricting draining of the water or the pump itself is faulty

Whirlpool... | Answered on Sep 28, 2019

Go to the Whirlpool web site, click on support, then select Instructions for Use (or Manuals & Literature, whatever... it should be obvious.) This will take you to a page where you type in the model number for your machine. After a quick search you will be able to download the .pdf file containing the instructions.

Whirlpool... | Answered on Sep 27, 2019

New sensor is required will not run if it cannot lock (safety)

Whirlpool... | Answered on Sep 24, 2019

Generally speaking the lid lock works either electrically by a solenoid or on older models when the tub spins it creates a breeze and a blade blocks the lid.

Whirlpool... | Answered on Sep 24, 2019

then don't open it after starting it

Whirlpool... | Answered on Sep 21, 2019

Not finding what you are looking for?
Whirlpool Logo

Family Lines

33,300 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts


Level 3 Expert

85222 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides