Tasco Science & Laboratory - Page 3 - Recent Questions, Troubleshooting & Support
Manual for a microscope
Try Ebay--may have to buy the micro aswell but it won't cost much,have you tried the Tasco website in case a free d'load is avail?-kind regards martin r
3/27/2009 11:50:31 AM •
Tasco 750...
•
Answered
on Mar 27, 2009
Fixing one
You must detach the bottom cover of the base of the microscope by taking off the 4 or 5 screws that keep it attached. That should reveal the wiring to the socket and bulb base.
12/22/2008 10:15:21 PM •
Tasco 750...
•
Answered
on Dec 22, 2008
Manual
I found out that Tasco microscopes have been discontinued quite some time ago. A Company called Bushnell 1-800 423-3537 who gave me the number of ABO 305-859-2010 Tasco microscope 750X # 60750-0 call after 3pm. They do not have my manual but can answer questions or send a similar manual. I have to call back stiil hope this helps. Zoom
3/19/2008 4:53:08 PM •
Tasco 750...
•
Answered
on Mar 19, 2008
Problems with viewing under low magnification (20x) only red stain
hello..
For the red colour partical your illumination angle should be 0 degree.
As per you exepirience you are getting red at low magnification and not getting at high magnification. at the higer magnification the light deviation you can apriciate more then lower.
try to adjust your light source focusing lenc at higher magnification so at the lower it will be more better,
for the further problem you can contect me any time,
regards.
INDRAVIJAY
3/10/2008 4:26:13 PM •
Tasco 750...
•
Answered
on Mar 10, 2008
Microscopes
sir,
Diffrent company having their own system for microscope arm balacing.
Tell me which one microscope you have.
Auxillary arm or microscpe body sloly come down ward.
tell me problem is consult with which part..
INDRAVIJAY
3/10/2008 4:02:28 PM •
Tasco 750...
•
Answered
on Mar 10, 2008
Optic lens tube separation
sir,your microscope tube with the eye piece is screw joint with microscope body. Rather part is friction fitted as well as there is a proper place to mount it.you can do the gluing but first of all be clear that part should be not a movebale part other wise you will have dificulty for fine focusing.
for the further quotation dont be hazitate,
INDRAVIJAY
3/10/2008 3:49:47 PM •
Tasco 750...
•
Answered
on Mar 10, 2008
AA-Spectrometer Unicam 939 Error
The error you are experiencing on your Unicam 939 AA-Spectrometer with the software reporting error 16 and 2, along with lamps 1,2,3,4, and 10 lighting up, could indicate a few different issues. Here are some steps you can take to try to fix the problem:
- Restart the spectrometer: Turn off the spectrometer and unplug it from the power source. Wait a few minutes, then plug it back in and turn it on again. Sometimes, a simple restart can fix issues with the instrument.
- Check the calibration: It is possible that the instrument needs to be calibrated. Follow the manufacturer's instructions for calibrating the spectrometer.
- Check the lamps: If multiple lamps are lighting up, it could be due to a problem with the lamp assembly. Check that the lamps are properly installed and functioning. Try replacing any lamps that appear damaged or worn.
- Check the power supply: Make sure the power supply is functioning properly by testing the voltage output with a multimeter. If the voltage output is incorrect, try replacing the power supply.
- Check the communication between the software and the spectrometer: Ensure that the software is properly communicating with the spectrometer. Check that the cables are properly connected and that the software settings are correct.
If these steps do not resolve the issue, it may be necessary to contact the manufacturer for additional support or to seek the assistance of a professional repair technician.
3/24/2023 6:39:35 AM •
Science &...
•
Answered
on Mar 24, 2023
Eppendorf centrifuge model 5702: lid not does latch/lock after emergency release.
If the lid of your Eppendorf centrifuge model 5702 is not latching or locking closed after the emergency release, it is possible that the locking mechanism is damaged or misaligned. Here are some steps you can try to troubleshoot the issue:
- Check the alignment of the lid: Make sure that the lid is properly aligned with the base of the centrifuge. If it is not, the locking mechanism may not engage correctly. Adjust the lid as needed and try to latch it closed.
- Inspect the locking mechanism: Check the locking mechanism on both the lid and the base of the centrifuge for any signs of damage or wear. If you see any damage, you may need to replace the locking mechanism.
- Check the safety interlock switch: The safety interlock switch is a small button located on the base of the centrifuge that is depressed when the lid is closed. If this switch is not working correctly, it can prevent the lid from latching closed. Check that the switch is functioning properly by pressing it with a small tool while attempting to latch the lid.
- Contact Eppendorf customer support: If none of the above steps work, you may need to contact Eppendorf customer support for further assistance. They can help you troubleshoot the issue and provide advice on how to proceed.
3/15/2023 4:55:19 AM •
Science &...
•
Answered
on Mar 15, 2023
Not finding what you are looking for?