Stanley Cutter Tools - Recent Questions, Troubleshooting & Support

You do not have to remove any screws. Extend the blade outward using the thumb slide on top of the knife. There is a small black pushbutton on the opposite side from the lock button. Depress the button on the side and using the other hand, grab the blade with your thumb and forefinger to pull the blade out. It may require a little wiggling. Now the new blade can be slide in and locked into place. The black pushbutton controls the locking mechanism that keeps the blade from pulling out.

In terms of functionality and features, Stanley FMHT10288 Retractable Knife is quite satisfying. The knife is considered as one of the best kitchen knives. The price remains in the lower range. So, as a budget friendly option, Stanley FMHT10288 Retractable Knife can be quite a fine choice for you indeed.

Hmmmmm.... that sounds really confusing. Better yet... just watch this video! http://www.youtube.com/watch?v=B8Q1p-8jkyEIt's actually pretty easy! :)

I agree. The packaging is ridiculous. I removed it by grasping the packaging and pulling (very hard) from the blade end (bottom left as looking at it) straight out. This stretched and tore the plastic "paper" and pull the knife free.

Slide the blade holder all the way out, press on the tab as shown in picture. Pull on blade with other hand. Blade slides right out.

at the handel end it will pull apartthen slide the whats left of the old blade and put new won in its place just do it slowly so you dont forget how it goes

Some models has 2 screws on the knife case.unscrew them and you can access to the blade.

HI!Kindly pull the button on the end of the knife and then after you remove that you can now put the blade of your knife.

This is the closest thing I can find. Click here.
Otherwise, write Stanley support and they'll answer you here.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

there is a little black button on the end where the blade comes out. With the blade in the out position,push in the button and pull out the blade. With button pushed insert new blade or turn the old one around to use the other end.let go of the button and you are ready to go.

Hi.

See here the Stanley knife disassembly. If you have a 99E there may be an additional plastic part that is not shown in the diagram. The plastic tab is located at the back of the blade.

This knife is ****. To load... you have to push the slide all the way forward. Make sure the switch is set to unlock. PINCH THE BLADE WITH YOUR FINGERS AND WIGGLE IT INTO PLACE. Then you have to use every ounce of thumb power to relock the switch.

Once you are done, the blade will still come out in 9.9 / 10 times you cut something.

the blade section pivots to swivel when doing that it allows you access to the blade storage area that holds up to 7 blades, if the extra blades arent in place perfectly the handle won't close properly, if your problem is with the blades themselves, make sure that the slot in the blade is aligned with the holder perfectly

At the back end of the knive (the curved end) press the black piece through the yellow rounded part and the yellow front and the black back will part, now slide the yellow part back to reviel the blade folder. Fit new blade then refit the yellow part on top of the black part and slide the yellow part foward to lock it back in.

If you use the wrong brand of blades, they won't let the knife shut all the way. The notch is cut slightly differently. The same is true for the Kobalt knife I just bought at Lowes. Get the Stanley blades that are right next to the knives - they are the only ones that work.

Sorry.

If you bought the Stanley blades, then I don't know what the problem is. Sorry for that too.

I was able to find the answer on another site. It is really simple when someone tells it to you. You push the blade all the way out then you can push the yellow button and it comes out.

copy and paste link https://www.manualslib.com/manual/97951/Makita-Dpc-6400-Dpc-6401-Dpc-7300-Dpc-7301.html?page=17

Hi, please replace the batteries first. If that does not work, please attempt to factory reset your device ( can reference manual). Thank you.

A pipe cutter is a tool that plumbers use to cut pipes. It gives a much cleaner and better cut than saws.

check base groove for debris / damage