Shopnbc Blenders - Page 3 - Popular Questions, Answers, Tips & Manuals

Contact Delfino/Toastess to inquire.

This problem can come from both the blender and or even the circuit powering it. First make sure that the outlet you have your blender plugged into is powered and not ripped If your blender still is not turning on then you may have a faulty motor or motor connection. Or the fuse could be blown and needs to be replaced.Or it could also be jamming for this you must first need to disassemble the drive and then turn the blade shaft. If it seems to be stuck or jammed here check what is the causing it to be jamming. In most of the cases it is debris that are stuck in the blades of the blender that causes it to be stuck.

The lighter flickering on your blender is letting you know that it is not working.Make sure that the blender isn't jamming Another possible cause of the blender not working maybe because of it jamming. For that you must first have to disassemble the drive and then turn the blade shaft. If it seems to be jammed, check what is the causing it to become jammed . In most cases it is debris that are stuck in the blades of the blender that causes the jamming.Or it could be the fuse went bad and needs to be replaced.

Most likely by replacement

The shaft has probably become tight in the bearings and the assembly will need to be dismantled for cleaning and possibly lubrication - I am unfamiliar with the Ninja but the average blender is a fairly basic mechanism and not many fasteners have to be removed before the parts needing attention either fall off or can be removed. It is a fairly intuitive process for the handy person. You could perhaps start with the nut on the blade - there seems enough exposed thread to judge whether it is left or right hand thread and it shouldn't be particularly tight. Lots of cloth should be used when holding the blade...

https://youtu.be/dklwnGPwHVw

The thermal fuse must be in intimate contact with the motor so when the motor temperature climbs dangerously high the fuse temperature doesn't lag far behind. I have seen the thermal fuse buried in the windings of a transformer so it isn't beyond the realms of possibility it could be inside the motor. The thermal fuse body is metal and live and so must be insulated and so is generally found in the supply wire inside some heat resistant sleeving strapped firmly to the motor...

https://www.ebay.com/c/1253876678 https://youtu.be/SLZ67bOeaNQ

The blades may not be turning because the blade assembly is not fully tightened onto the blender bottle. Another reason could be that you are not putting the blender bottle and blade assembly into the blender base in the proper way. For more answers visit the Oster Blend-N-Go My Blend troubleshooting page: Oster Blend-N-Go My Blend Troubleshooting

https://www.amazon.co.uk/Gordon-Ramsay-Cooks-600w-Blender/dp/B003UTUO2M

fixya doesnt sell products

so order one fixya doesnt sell products

https://www.youtube.com/watch?v=LfY_-VA5m8A https://www.youtube.com/watch?v=AhXiPiaie1I

Hello, Rebecca - Please see my reply here: https://www.fixya.com/answer/answerpageslideview.aspx?thid=29753915&ctg=142&brd=3705 Best wishes.

Are you twisting in the right direction to release. I think you put on and twist to lock and twist the other way to unlock. https://www.youtube.com/watch?v=JPKGp3KFjcY https://www.youtube.com/watch?v=4XehR2C_6n0 manual https://www.manualslib.com/manual/1444596/Starfrit-024300.html?page=6#manual

you checked at your nearest electronic shop,I think the motor available in that shop

https://youtu.be/i5E-t09PFL4 you watch this video & your problem is solved

Is probably a binding problem with the motor shaft bearing or the circuit card is fried. If you've tried giving it a good cleaning and that didn't work it's a good bet the unit is junk. Suggest buy a new one.

blenders are: power cord, switch, speed control, and motor. A disassembly and VOM meter is required to determine which part is defective.

https://www.bakedeco.com/images/manuals/USD-R-5AM.pdf