If you have downloaded the software for your Sharp AR-5316E printer, but encounter a paper problem message when trying to print from your desktop while photocopying from the same printer works fine, there could be a few potential issues to consider:
Paper settings: Make sure that the paper settings on your computer match the paper size and type configured on the printer. Check the printer properties or print settings on your computer and ensure they are correctly set to match the paper loaded in the printer tray.
Paper tray configuration: Verify that the paper tray is properly loaded with the correct paper size and type. Make sure the paper is aligned correctly and not jammed or skewed in the tray.
Printer driver: Ensure that you have installed the correct and up-to-date printer driver for your Sharp AR-5316E printer. If you downloaded the software from the manufacturer's website, it should include the appropriate driver. Consider reinstalling the driver or updating it to the latest version to ensure compatibility with your operating system.
Printer firmware: Check if there are any firmware updates available for your printer model. Firmware updates can address compatibility issues and improve overall performance. Refer to the manufacturer's website or user manual for instructions on how to update the printer's firmware.
Paper sensor or other hardware issues: If the problem persists after checking the above steps, it's possible that there may be a hardware issue with the paper sensor or other components in the printer. In such cases, it's recommended to contact Sharp customer support or a professional printer technician for further assistance. They can provide specific troubleshooting guidance and help diagnose and resolve any hardware-related problems.
It's important to ensure that all connections are secure and that the printer is in good working condition. If necessary, consult the printer's user manual or contact customer support for detailed instructions specific to your printer model.
you may gey the driver software for AR=5316 printer install sotware inthese websites http://nodevice.in/driver/AR-5316/get47086.html http://ptf.com/sharp/sharp+ar+5316+printer+drivers+to+support+windos+7/
I hope you didn't run the microwave with nothing in the cavity, if you did, it will damage the magnetron.
The turntable dishes do get hot depending on the quality of the glass used to make it. Heat is caused by impurities in the glass.
If you run it with no food in the oven, the glass will try to absorb the energy with atastrophic results usually.
Question edited for clarity, 'sharp at 5516' to 'Sharp AR-5516'.
Remove the toner cartridge and clean the contacts on both the cartridge and the copier with alcohol. Tap the cartridge on both ends to settle the toner. Make sure you are using genuine Sharp replacements.
..
It is possible there is a small slot in the back, sometimes under the cover that covers the ribbon. should be an opening may have arrows on it that shows where the paper goes
This would mean that either a CABLE BOX, SAT BOX, COAX CABLE, HDMI CABLE, ETC may not be working properly, something is loose, or needs reset. -Reset ALL components by unplugging them for 5 minutes including the TV. -Be sure all COAX CABLES and HDMI CABLES are tight and properly connected. -If you CAN pull up the TV MENU when you have the black screen, update your TV’s firmware to be sure your TV is up to date and rule out the TV as the problem. NOTE: If the TV now works and there is no BLACK SCREEN, the issue was either a loose cable, old TV firmware, or a component that needed to be reset and the issue is now resolved.
You will need to preform a power drain cycle on your TV here.Unplug your TV from the power source.Press and hold the power button for about 10 to 30 seconds.This will help drain all of the TVs residual power. Now plug the TV back into the power sources.
How exactly did you test the backlight strips Mike? This set is made by Hisense, they have the tolerances really tight on the backlight inverter current, in our shop we have seen many times on Hisense sets with no backlights not working, we test the lamps with our tester and all worked, however when new strips were installed the set worked as it should. One thing I want to verify, when you say black screen, you're not talking about a real dark blue screen where the lamps work and you're missing video? Reason I ask this is you said you replaced the t-con board, that's something that would be replaced if you had backlights and no video as the tcon has NOTHING to do with the backlights
Hey, The Sharp LED Backlight TV model 2T-C45AD8X's back cover can be opened by performing the following steps:
1) Cut the TV off from the power supply.
2) Place the television flat on a soft surface.
3) Using a screwdriver, find the screws that are attached to the back cover's borders.
4) Carefully remove the back cover to have access to the internal parts.
Thanks!
You need new LED backlight strips, a power/inverter board can cause this as well but on Sharp-Hisense sets it's been the backlights that are bad in most sets we repair in our service center.