Rowenta Irons - Answered Questions & Fixed Issues

You fill it from the hole in the nose. It comes with a small container that has a pouring lip. https://www.google.com/search?q=Rowenta+model+DE-871B+manual ..

replace it --switch fail

I have the same issue. The steam on/off switch fell into its cavity and does not work. Looks like the plastic housing on the top of the iron can be removed, does anyone know how?

All the Manuals to all of the Rowenta Steamers. https://www.rowenta.ca/en/instructions-for-use/Products/Linen-care/Garment-steamer/csc/GarmentSteamer ..

Page 5 of the manual onwards Lenora https://images-na.ssl-images-amazon.com/images/I/81Qca7gcYWS.pdf https://www.rowenta.ca/en/instructions-for-use/Products/Linen-care/Garment-steamer/csc/GarmentSteamer ..

There is an issue with the irons thermostat. You will need to buy a new clothing iron.

To open the Rowenta Superpress 050 iron, you should first unplug the iron from the power source for safety. Then, locate the water reservoir button on the top of the iron. The button is usually located near the back of the iron. To open the reservoir, you need to push the button inward and turn it counter-clockwise. This will release the reservoir from the iron's body, allowing you to fill it with water. After filling the reservoir with water, you can reattach it to the iron by aligning it with the body and turning the button clockwise until it clicks into place. Remember to never fill the reservoir above the maximum fill line, as this can cause the iron to leak water or even cause damage to the iron.

Hi,
Welcome to Fixya. If the iron wont turn on it can be caused by a faulty cable, a busted Fuse, transistor, capacitor, switch problem or the main board of system. If you have warranty then you can have it checked an repair for free or if you have knowledge with electronics then you can open the iron and check hte part that is bad
Thanks

check out the videos that show how it's done. https://www.google.com/search?q=Rowenta+1700+iron+replace+damaged+power+cord ..

Question edited for clarity. Question moved to correct category. The search query really need the numerical model number. https://www.google.com/search?q=Rowenta+Inox+Surfline+manual ..

To try and seal the water leak will possibly render the appliance dangerous. I would speak to Rowenta and ask the question. They may well extend the warranty if you suggest it wasn't used for say a few weeks after purchase etc.

The steam tank may not be heating because of mineral deposits in the tank. But also do this check first. Open up the tank reservoir cold, and drain all water out, (is it clean inside there when you shine flashlight in there? Rinse with clear filtered water only (low minerals).

Do not use CLR or anything agressive in there. You should have the main unit in full steam mode and the iron control also in full steam mode. Leave one tablespoon of water in the tank, put back together and let the pressure build. Put a clean towel on your ironing board and when iron is at full pressure and heat, hit the burst of steam and look at what comes out of the sole plate. If you see lots of white deposits look at the sole plate and see if the white chunks are coming out steam holes.

When using iron, run it till steam/water tanks are dry, the burst of steam is used in this case to clean the iron of all standing water. Pull the reservoir and allow to cool...once tank is cool drain it as well. Doing this several times should help purge unit of the heavy mineral deposits.

If you need parts, here is the Rowenta repair facility....
California Electric Service in Concord CA (it is the only Rowenta repair station in California) go to either of the following addresses:
their website is: http://www.californiaelectricservice.com/
or tech service: [email protected]

time for the bin not worth fixing

We’re u able to fix this ? I am facing similar issues after my wife forgot to shut it off and the auto shut off might have triggered but now it doesn’t Heat up even though I the light comes on

RCD or MCB that is tripping? If MCB the iron is overloading the circuit, usually a short circuit and is often related to the power cord. If RCD power is escaping from the circuit to ground and is usually caused by an internal water leak.

The fine fibres at the surface of linen stand up like the bristles on a brush. Light coming into the fibres gets trapped. When you iron the linen, you flatten the fine fibres. Incoming light no longer gets trapped in the spaces between the fibres and instead is reflected (bounced back) like on a mirror. That is why linen looks shiny after ironing. To prevent this, use a damp cloth on top of your linen when ironing. This will flatten (iron) the linen material but not compress the fine fibres. Good look.

How to replace the fuse on Rowenta DG5030? Please help..

They are built to shut off after about 30 sec or so if the iron is not moving and the iron is in pressing position (sole plate down). They shut off if they are not moving and standing with the sole plate vertical, in about 5 minutes. If you move the iron (like ironing) they reheat. If it doing something else the electronic control is defective. It is cheaper to replace than repair.

Similar models manual: https://www.rowentausa.com/instructions-for-use/Products/Linen-care/Steam-generator/Compact-Steam/csp/1830006489 https://www.rowentausa.com/instructions-for-use/LINEN-CARE/STEAM-STATION/COMPACT-STEAM-STATION-DG7530/csp/1830005479 https://www.rowentausa.com/instructions-for-use/LINEN-CARE/STEAM-STATION/PERFECT-STEAM-STATION-DG8520/csp/1830005299

I'm on my fifth Rowenta iron. The first four eventually started to leak. I keep buying Rowenta because I get the best results except for the leaking. I've been using filtered water even though the manual sas to use tap water. I will start o use tap water. The fifth one I bought was highly rated by Consumer Reports. If this new one starts to leak, I'll bring it back and buy a different brand.