Panasonic Cameras - Recent Questions, Troubleshooting & Support
Lumix camera charger green light flashing
I had a blinking green light on the charger when I would put the battery on the charger. I noticed some black buildup on the prongs of the battery and scrapped it off and now the battery charger is displaying solid green. It may end up being a quick fix considering my equipment came from ebay and already had some light wear and tear
Panasonic Lumix System Error (zoom)
Hello
The problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the
probability is that you will have to get it fixed by a professional.
Use
these at own risk as it may further damage the camera.
Firstly ,
try connecting your ac adapter or usb cable.
Try holding the
shutter button while switching on the camera.
Look at the lens ,
and if some of the lens 'circles' is misaligned or not concentric then
try wiggling it (while holding camera lens down).
Try gently
pushing or pulling the lens when it extends but this is risky as it may
cause the lens barrel to slip out of its guidance system.
Another
way to do this is to place the camera lens down on a hard surface and
then power it up. Be sure to use a soft cloth or something similar as to
not scratch your lens or casing. Let the lens push the camera up and
down a few times and sometimes the little resistance provided by the
camera is enough to get things going again.
Try hitting your
camera near the lens on the body with the soft tissue on the palm of
your hand.
Other than that , I would take the camera to a repair
center for a evaluation to see if it would cost more to repair than to
replace the camera.
If it is still under warranty I would suggest
you take it in before trying any of these steps and remove any
off-brand batteries or accessories as some stores are really fussy about
warranty repairs on camera's with non-brand accessories.
You can also have a look at THIS link.
Hope
the advise is useful. please do not hesitate to let me know if you need
any further assistance. Also, please be so kind to let me know if you
found this helpful.
Regards
Andrea
I have a panasonic Lumix camera and it keeps
Hello and Welcome to FixYa!
There is a Lock switch on the left side of the SD card. Make sure the Lock switch is slid up (unlock position). You will not be able to modify or delete the contents on the memory card if it is locked.
You can see the snap attached below;
If the lock switch is not on lock;
- Slide the switch up and down. Repeat this 3 times.
- Let it stay on the Lock position for 30 seconds.
- Slide the switch up to unlock the card.
- Try to transfer files into the device.
If none of the above works, then you card in either damaged (Format it) or is Password protected.
If you think I was of help, your token of appreciation in the form of rating and a testimonial will be esteemed.
Concerned, Nooh
11/28/2023 7:18:52 PM •
Panasonic...
•
Answered
on Nov 28, 2023
I want to change language from Japanese to English Panasonic CN H500D
To change the language on your Panasonic CN-H500D, press the "Menu" button on the remote control. Use the arrow keys to select the "Setup" option, then press the "Enter" button. Select the "Language" option, then press the "Enter" button. Use the arrow keys to select the language you want to use, then press the "Enter" button. The language will now be changed to the one you selected.
2/21/2023 10:01:11 PM •
Panasonic...
•
Answered
on Feb 21, 2023
There is a spot on the top left hand side of the LCD monitor, and this spot also appears on the prints
Hi,
Looks like dust must have gotten onto the CCD sensor (or, more specifically, onto IR-cut filter on the sensor). The dust enters the lens through the gaps between zoom barrels and sometimes ends up on the sensor-which is what most probably happened here.
There are 2 ways I know to remove the dust. 1st way-it might sound silly, but try sucking the dust from the camera with your mouth around the closed lens :) Make sure you don't blow any air in. This worked for me a few times. Note that sometimes it might make the problem worse as you might move other dust particles onto the sensor.
If 1st way didn't help then you can try directly blowing the dust off the sensor. This should only be attempted if you're happy with partial dismantling your camera and are ok taking the risk of ruining the camera further. Although in my opinion lumix cameras are generally fairly easy to repair, you will need steady hands and patience to attempt this. If you are happy to proceed, do the following:
1. unscrew the screws holding the back of the case
2. lift the case carefully a bit making sure you don't break the ribbon cables going to LCD and backlight
3. undo the LCD and backlight ribbons (there are black flaps on the connectors, these gently flip upwards)
4. gently remove upped logic board. Try to pry it in stages from all sides, don't just pry it up in one go from one side or you might damage the connector. (I learned the hard way ;)
5. on the bottom logic board you'll see 2 connectors, undo the upper one to release the ribbon going to the sensor (note that this is not absolutely necessary if you're happy cleaning the sensor without disconnecting it-it can be done, the ribbon is relatively robust.)
6. the sensor is held by 3 tiny star screws. if you don't have the exact screwdriver you should be able to use a small flat screwdriver to carefully unscrew them. Do the screws bit by bit, i.e. unscrew 1st one a bit, then unscrew 2nd one a bit, and so on
7. there is a small spring underneath the sensor assembly, make sure you don't lose it :)
8. once the screws are undone you have access to the sensor-lift it up. Under good light you should be able to see the dust bits. Use a blower to get rid of them.
9. that should be it. put the camera back together. figers crossed it will power up and the dust problem will be gone :)
NB. You might have come accross horror stories of people being electrocuted by flash capacitors when repairing cameras. This might indeed happen. It's not easy with FX8 though: To get electrocuted here you would need to undo the top plate, unscrew the switch logic board and remove protective tape off the flash circuit, then touch the capacitor contacts :) Don't do it of course. Not worth it.
Good luck,
Raf
My panasonic vdr150 pc mode not working
It sounds like you are having trouble using your Panasonic VDR-D150 camera in PC mode. Here are a few things you can try to troubleshoot the issue:
Make sure that the camera is properly connected to your computer via the USB cable.
Check that the camera is turned on and in PC mode.
Check that your computer recognizes the camera as a device. You can do this by going to the "Device Manager" in the Control Panel and seeing if the camera is listed under "Imaging devices."
If the camera is not listed in the Device Manager, try unplugging and re-plugging the USB cable and restarting your computer.
If the camera is still not recognized by your computer, try using a different USB cable or a different USB port on your computer.
If none of these steps help, it is possible that there is a problem with the camera itself. In this case, you may need to contact Panasonic for further assistance.
12/24/2022 10:12:47 PM •
Panasonic...
•
Answered
on Dec 24, 2022
System error (o.i.s)
Hi,
This error is for the optical image stabilisation.
Generally the camera should be ok after your turn it on and off again.
The error you are getting is because either the OIS has malfunctioned
or is stuck.
I suggest that you take out its memory stick, the
battery etc and keep the camera like that for about 15 minutes. Then
only reinsert the battery (fully Charged) and try to power on.
Try a little tap ( but not too hard) on the side of the camera....this
might realign if the OIS has got misaligned. If you are lucky, you would get if fixed.
If the problem still persists, you need to contact Panasonic.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
DO ACCEPT THE SOLUTION IF 100% SATISFIED.
Not finding what you are looking for?