Maytag Dryers - Recent Questions, Troubleshooting & Support

check the drum support rollers

Maytag Dryers | Answered on Nov 23, 2019

I don't know what it means but you can try to reset the control panel by unplugging it for 10 minutes then plugging it back in. This may or may not help but it works every time my dryer gets stuck on or off with the panel display showing something odd, or stuck on so many minutes left but it doesn't ever stop. It won't cost you anything to try this. If it happens very often you may need the panel replaced.

Maytag Dryers | Answered on Oct 27, 2019

I'm having trouble finding the exact capacity of your dryer, but I believe it is around 7.0 cu ft, which is about as large as you can get in a standard-width home dryer.

Maytag Dryers | Answered on Oct 14, 2019

Most likely cause is a thermal fuse or the heating element. And if it's a thermal fuse, you need to make sure the dryer vent is clear and un-restricted, since that is the most common cause of thermal fuses blowing.

Maytag Dryers | Answered on Oct 05, 2019

You have to work from the front. Pull the top then the front then you will be able to see everything. Pretty self explanatory.

Maytag Neptune... | Answered on Oct 02, 2019

be very careful with electricity. fuses are in the home's wiring. open the dryer door. if possible follow the wire
from the large plug back to the home's main electrical panel. there may be a small panel just for the dryer or it may be connected directly into the main panel. locate the fuses if used, unscrew them and replace them with ones you know are good or use an electrical meter to test the original fuses for continuity. install good fuses.
if your system uses circuit breakers, locate the breakers and look to see if they have been moved from the on position. switch them off and on a few times and leave them on. go and close the dryer door and choose a new dryer setting to try to see if your dryer works. great if all works as it should. if dryer won't start or fails again, you need to have your house wiring inspected or your dryer repaired. call for help without delay.

Maytag Dryers | Answered on Oct 02, 2019

i don't know. consider shutting off dryer, open the dryer door, turn off the main electrical source [shut off circuit breakers for dryer or unscrew fuses.
shut the dryer door and turn breakers on and or fuses in. this may reset your machine's internal program.
choose a new timed setting to see if all is OK.

Maytag Dryers | Answered on Oct 02, 2019

It may seem crazy, but you have to remove the dryer door, and then take the door apart to be able to replace the handle! I've tried doing it without taking the door apart, and I only ended up damaging the door and replacement handle!

Maytag Dryers | Answered on Sep 02, 2019

I did A & B, B actually did the trick and I have had absolutely no problems.

Possible Solutions
Power unit down by turning off the circuit breaker(s) for one (1) minute.
  1. Power unit up by turning on the circuit breaker(s).
  2. Start a time dry cycle.
  3. Monitor the dryer for one (1) minute to ensure the error code does not display again.
It indicates that the lint screen or vent is clogged; the vent is crushed, kinked or has too many turns. ... The dryer will continue to run when this diagnostic code is present.

My dryer did the same thing. I cleaned all the vents thoroughly, if you are unable to clean inside where the vent screen is try this. remove lint screen, using tape or rubberband attach a empty paper towel roll to the end of your vacuum crevice tool. Also at the 99 cent store I purchased a appliance brush to loosen any lint inside before vacuuming. The brush works better then the one I purchased from Home Depot for $15.
Vacuum the inside of the dryer, be sure to vacuum the very back inside and around the door.
This is the tricky part now.
The dryer flex hose actually has to be set just right. If the placement is incorrect you will get the error codes, dryer turns off after mins etc.

Here is a Flex hose tip video. Hope this is helpful

Maytag Dryers | Answered on Aug 24, 2019

if you are turning it from the inside of the dryer with ease then check to see if belt broke.

Maytag Dryers | Answered on Aug 18, 2019

Only thing that comes to mind is,  it may be in "advertising" mode

Try Pressing the damp dry and sensor dry keys
for 5 seconds will take it out of the 
Advertising mode.

(In Advertising mode No functions will be run
except illuminating the LEDs.)

Maytag Dryers | Answered on Aug 16, 2019

Check you flame. If the flame is very short (less than half way down the burner tube, it can be a gas pressure regulator failure. They are adjustable but that usually indicated it is about to fail. Make sure the flame ignites every time you hear the relay and solenoid valve click. The is a small panel on the front that can be removed to see the burner and the pressure regulator. The is a glow igniter that comes on several seconds before the gas is admitted. Confirm that works. Check at the dryer vent whether you smell gas once and a while which would be an indication of a failure to ignite.

Maytag Dryers | Answered on Aug 12, 2019

have you checked the relay for the igniter and confirmed there is power to the igniter?

Maytag Dryers | Answered on Aug 12, 2019

Not finding what you are looking for?
Maytag Logo

Family Lines

11,449 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Dryers Experts


Level 3 Expert

85216 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Are you a Maytag Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides