Kohler Plumbing - Page 6 - Recent Questions, Troubleshooting & Support

You can find it on amazon here: Save on Kohler Innovative Cimarron Toilet. Hope this was helpful. cheers

Check that it's hooked up correctly. I've seen this exact problem when the hot water is hooked to the cold side of the valve.

There is a threaded rod in the over flow line. Take the plate off adjust shaft by screwing it out making it longer so the stopper opens more, or screwing it in to make it shorter so it will close the stopper sooner.

Remove sprayer and hose from faucet body. Remove handle and cartridge. Pull up on body. Replace parts and reinstall in reverse order.

under the neck there is a o-ring it is starting to go bad.call a plumber to fix if you can't do it yourself.

www.us.kohler.com/us/...Support

www.us.kohler.com/us/...Support

The plug has a little hole in the end - that rocker-arm lever fits through the hole. If the plug gets turned 90 degrees to the side before installing the lever, the lever won't go through the holeand the popup won't pop up. Pull the lever back out, rotate the plug 90 degrees with your fingertips or thumb, and put it back in. It may take several tries.

Under the sink, you mean? Around the tailpiece? Loosen the tailpiece nut and Seal it with "plumber's putty", then snug it back down.

Get in touch with the company that made it. Allot of times the company has a lifetime warranty on their faucet.

Don't quite know what your question is...

what is your ? u need to give more information so we can help with the problem.

Hi! Yes it sounds like the spray diverter needs replacing. Kohler .com will have this part online or you could try a plumbing supply shop.

Should be a small screw, hex or wingnut that attaches pull rod to rest of pop up assembly, just re-attach rods and tighten screw firmly. If you need further help, reach me via phone at https://www.6ya.com/expert/frankie_091f536560a54e12

Here's Kohler's help page. Maybe you can find the answer there. If not, maybe someone else will be able to help. Until then you can try here http://www.us.kohler.com/us/static/helpTopics.jsp

Shut off water supply Under Sink: · Unscrew brass connector for spayer hose · Disconnect single water line to faucet bysqweezing lever on connector and Gently pulloff. · Loosen two screws on faucet base washers thenunscrew the washers on thebrass faucet shaft ( NOTE: Have someone hold the fauct so it does Not accidentlyfall in sink when the support washers are removed) · Take faucet out of sink · Unscrew brass collar at base and remove · Remove Set Screw on lower body of faucet · Pull out Brass Mechanism from faucet · The Diverter is located in the Brass mechanism · Remove the Washer · Pull off the small top valve in center of theDiverter, if still there · Using a large wood screw that fits/screw intothe exposed hole In the center of The plasticdiverter, screw it in and pull out the remaing part of the old diverter · Flush out Faucet to remove any remaining debrie · Replace with new diverter and replace washer · Grease all areas that where greased when mechanismwas removed Remove & clean the faucet Airrater and replace only afterEVERYTHING has been Completed soyou can flush the faucet out again into the sink, then replace.

after you take the handle off,the hose needs to be taken off for the faucet body to be pulled up to get at those o-rings

http://411plumb.com/kohler-forte-faucet-troubleshooting-repair-guide/

You may have a good idea about the locations of the 3 o-rings when you have a look at the last page of the installation guide. Here is the link for the guide: http://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1084448_2.pdf