KitchenAid Microwave Ovens - Recent Questions, Troubleshooting & Support


Yes, unless a technician may have removed it during a previous service. It should be located behind the controller assembly, sometimes in a small envelope.

At my Web site, I have a video showing you how to remove a typical microwave controller in about 5 minutes.
http://www.microwavecontrol.com

if you have other questions, please feel free to contact me directly by email through the Web site or at pupista@gmail.com
11_14_2019_1_57_44_am.jpg

KitchenAid... | Answered on Nov 14, 2019


Yes, it is probably a bad relay. Usually appliance techs just replace the whole control board, because those relays can be hard to find and buy.

KitchenAid... | Answered on Oct 14, 2019


Yes, it is most likely a bad relay on the control board.

KitchenAid... | Answered on Oct 05, 2019


Hi Jill, what the screen indicates is that the door is not closed
There are a number of internal contacts that have to be closed for the microwave to work
If any of them are wrong, they can give you that information.
Depending on the brand there may be between 2 or 3 contacts in the door area that generate that warning
Indicate brand, model and type of equipment you are commenting on, in order to find the best possible solution
I wait your answer
Regards Franco Dosil

Hola Jill, lo que te indica la pantalla es que la puerta no esta cerrada
Hay una serie de contactos internos que tienen que estar cerrados para que el microondas funcione
Si alguno de ellos esta mal puede darte esa informacion
Derpendiendo de la marca pueda haber entre 2 o 3 contactos en la zona de la puerta que generan ese aviso
Indica marca, modelo y tipo de equipo del que estas comentando, para poder encontrar la mejor soluci?n posible
Espero tu respuesta
Saludos Franco Dosil

KitchenAid... | Answered on Sep 12, 2019


There are interlocks and micro-switches to prevent accidental running with the door open. The issue with the lock is preventing operation. You need to have it professionally serviced.

KitchenAid... | Answered on Sep 09, 2019


common problem with lots of MWs - the door switches are not set and secured properly. Now they are totally off. Need to pull apart and reset. Not a task for an average homeowner. Mine (Whirlpool) did that 1 week after I got it - exchanged for a new one.

KitchenAid... | Answered on Aug 07, 2019


Hi. this code represents a key pad or control board malfunction. you will have to make sure the key pad or control panel connectors are connected tightly and securely. If the wires and connectors are secure, the actual control board may be faulty and you will need to replace it at this point.

KitchenAid... | Answered on Aug 07, 2019


I started having the same problem with my KBMC140HSSO. You cannot see the error codes without disassembling the control panel (the codes are on another display that covered by the front panel). After doing so I found the error code to be F2, E3 which is "Key held down too long, or key shorted". I am ordering a replacement keypad and will report back if this fixes the problem.

KitchenAid... | Answered on Aug 07, 2019


You can find helpful Kitchenaid parts diagrams and get parts at affordable prices for most models from The Pros by entering your model number here:
http://tinyurl.com/gv383

KitchenAid... | Answered on Jun 30, 2019


Chances are the door panels separate as shown in the photo I have attached below. Panel replacement can usually be done without removing the door from the microwave. In cases where it is felt that door removal is necessary, I recommend detaching the door from the hinges. I generally do not advise removing the hinges from the microwave. Whenever the hinges are removed, great care must be taken to put them back in the very same position they were in. Failure to do so can cause microwave leakage, which can cause risk of skin burns, fire, and disruption of nearby electronic devices. You can find exploded view diagrams and order parts here: http://tinyurl.com/gv383 We have critical safety and disassembly info at our site, which is linked at our listing here on FixYa: http://tinyurl.com/yzjozk

KitchenAid... | Answered on May 01, 2019


For the KitchenAid microwave, model: KHMS2050SSS2 I found that i did not have to remove the screw. what i did was loosen the screw as much as it would go before getting tight again.(hard to screw) then on the bottom end of the door hinge (lying on its side) i pryed the bottom hinge off its mount. (with flat head screwdriver) from there i was able to get at the screws to separate the black surrounding stuff from the outside door... then finally i could get inside to get at the door panel controls. I noticed a whole bunch of condensation and on the back of the touch panel (electrical board).. i will replace that part as I think that is the culprit as to why the keys get pressed randomly, beeping randomly and wonkiness :)

KitchenAid... | Answered on Mar 15, 2019


Adjust the door switch mounting strip as adjustment is provided if not o.k check door switch connector on the PCB assembly for loose contact or soldering.

KitchenAid... | Answered on Mar 05, 2019

Not finding what you are looking for?
KitchenAid Logo

1,477 questions posted

Ask a Question

Usually answered in minutes!

Top KitchenAid Microwave Ovens Experts

William Miller
William Miller

Level 3 Expert

9179 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1691 Answers

Are you a KitchenAid Microwave Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...