Kenmore Water Filters & Coolers - Popular Questions, Answers, Tips & Manuals

A few troubleshooting steps you could try: Check the Power: Ensure that the unit is properly plugged in and the circuit breaker hasn't tripped. Check the Cold Switch: There should be a cold switch on the back of the unit. Make sure it's in the ON position. Temperature Limiter: It's possible that the temperature limiter may have tripped. You can try setting the hot and cold power switches to the OFF position, wait five minutes, then set the switches to the ON position. Wait 30 minutes for the water to heat or cool. . Mineral Build-up: If the dispenser has been used for a long time, there might be a mineral build-up in the tank that could be clogging it3. You might need to clean the dispenser to remove these deposits. If none of these steps work, it might be best to contact Hamilton Beach customer service for further assistance

Yes, there is normally an adjustment for both. It is a very obscure make. https://www.google.com/search?q=viva+bottom+load+water+cooler+adjust+the+cold+and+hot+water+temp ..

You may have spotted white and black flakes in water in the past. White flakes are created by mineral deposits from hard water, whereas black ones are caused by mold that develops in your water dispenser.

There are multiple possible causes. Check pages 12-14 (PDF pages 13-15) in the manual: https://useandcares.hamiltonbeach.com/files/840178600.pdf Note: if you hear the refrigerator unit running or feel heat at the hot water tank, you have power. Not listed in the troubleshooting guide in the manual: pump or valve unit failure. I don't see anything on venting for the water bottle either, so in addition to the steps in the manual, do a check of any venting on the bottle attachment assembly for clogging.

put some olive oil on the blue button and try to press many times in and out

You are my 40,000 question that I have answered! You don't get a prize, but I think that is pretty neat Paul :>D I have been here a long time. The manual only says that you have to make sure that cooling is switched on (Page 12). The unit has a 1 year warranty. If it out of warranty, you just need to pick it up and take it to a refrigeration engineer. It may need topping up with refrigerant gas. Consumer Support Questions? How to contact us: Telephone 800-488-5080 (Monday - Friday 8:00AM-5:00 PM ET) E-mail: [email protected] [email protected] https://useandcares.hamiltonbeach.com/files/840178600.pdf There are some videos here that might be of interest. https://www.google.com/search?q=Hamilton+Beach+Bl-1-3+water+cooler+not+cooling+the+water Hope the information helps you. ..

Contact them direct and tell them you want it fixed under warranty. https://useandcares.hamiltonbeach.com/files/840178600.pdf

Would be nice if you write what kind of car it is.

try resetting the filter

How to Set the Temperature on a Primo Water Dispenser

1. Move the Primo water dispenser away from the wall, being careful not to tip or spill the water bottle.
2. Locate the flat, brass-colored screw on the back of the water dispenser.
3. Turn the screw slightly clockwise for colder water or counterclockwise for warmer water. ...
4. Check the temperature of the water.

CHECK YOUTUBE SEARCH AS I found Hamilton cooler.

press the rest button or get a new cooler as the compressor is not working

pump failure --seal leak --kinked or damaged line

Contact Oasis to request the manual.

Refer to manual that came with unit. Big hint page 14 Even bigger hint and book mark this site. https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-50283-11.pdf

nope fixya doesnt sell products

turn the main stop **** off then repair and re seal were the leak is

First, I'm not a Earmark tech. * Contact your water provider for service. *** The following is for information only *** * common problems with priming bottom loaders. Here are some vids to help; https://www.youtube.com/watch?v=_ZV36EQnj4A * Set up (more technical); https://www.youtube.com/watch?v=239zY93bYrg Aloha, ukeboy57

Are you sure that the unit didn't blow its circuit breaker in the new location?

broken or stuck spring --bring back for repair or replacement