Kenmore Elite - Recent Questions, Troubleshooting & Support - Page 9

According to the manual, follow these steps:

• For an "F" error on your Washing Machine.
• Select PAUSE/CANCEL twice to cancel the cycle.
• Select DRAIN & SPIN if there is excessive water in the washer.
• Re-select cycle and press START.
• If the problem remains, call for service.

Here's the full manual: Kenmore 110.45986400 Owner's Manual

I don't just got done checking and sure enough it was filled with socks, rocks, and small debris. I don't know yet if it fixed it but will know in a few hours. In any case, these items could not have been good. First, try to make sure all water is out. Run on spin cycle for 10 minutes, be prepared for about 4 to 6 cups of water coming out.

the fix: You should always unplug for safety!
There are three screws at the very bottom of washer. You will need and extension and a star tip. They are on good and tight so I used a cordless drill and extension. I'm sorry I can't tell you which star tip I used. I bought a little security kit from harbor freight that has all these tips and one worked. Their is a white canister that has one hose in and another hose out. Just unscrew slowley and clean if dirty. You might be as surprised as I was if you find any junk.

Good Luck

The error code F29 indicates a problem with the door lock assembly. I recommend replacing the door lock assembly part number 8183270 searspartsdirect.com Please see the instructions provided below. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others. http://www.shopyourway.com/m/questions/1077653

go 2 repair clinic on line, same codes for whirlpool duet repair help then error code tab

YES BUT HAVE TO REMOVE CABINET TO GET TO IT

2 Beeps/E20--Error: Water dosen't drain. Cause: Drain is kinked or household clog. Correct.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

HOPE THIS HELPS

NO HOT WATER CHECK THE WATER INLET VALVE AS THE HOT COILS MAY HAVE GONE BAD U CAN CHECK FOR VOLTAGE AND FOR OHMS.. ALSO MORE LIKELY CHECK UR WATER TEMPERATURE SWITCH IT MAY HAVE GONE BAD , USE A METER FOR OHMS CHECK MAY ALSO WANT TO CHECK UR THERMISTOR ON MODELS WHICH HAVE ONE

as for ur pre wash u can just turn off machine for 20 minutes and pre soak items then turn back on. As for ur wet clothes check for loose worn belt if belt driven, or a loose slipping bad clutch and brake assembly. I would also check to make sure water pump is not clogged

You may have 2 issues here the leak from a bad or worn hose somewhere or a bad water pump seal. and the wet clothes as a result of a bad clutch break assembly, a loose worn belt, bad motor coupler etc depending if direct or belt drive

Needs new gaskets or seals.

check fusebox and power plug fuse

TOO many suds,use less soap

You may have a bad water valve,could be over filling. But. Still could be a drain pump. Does the tub ever fill with water when you are not using? Also too much soap and not using HE. Soap. Can cause this

they have a complete layout and schematics free Kenmore Appliance Parts Repair Parts

you must reduce water on faucet

"F22" is a door latch error code. The following link explains many causes of the error and possible recommendations to correct the problem:

http://www.fixya.com/support/r1976388-f22_error_code_whirlpool_duet_kenmore For an explanation of all the error codes, each one of these washers comes with a technical data sheet inside.

To access, you will need to remove the lower toe panel under the door. The access screws are located under the bottom front edge of the panel. You may have to prop the two front feet of the washer up for better access ( a 2x4 works well for this). With the screws removed, the panel should drop down, then come off. If the tech sheet isn't directly behind the panel, it will be affixed to one of the interior cabinet walls.

The tech sheet lists all error code definitions, troubleshooting data, diagnostics procedures and wiring diagrams. I mention the tech sheet because you may need it to troubleshoot this error code.


Replacement parts (if required) can be purchased at any of the following websites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

Prices vary between sites, so shop and compare. The first three sites listed also have helpful exploded view parts illustrations to assist you with locating and properly identifying the parts you may need.

Read through the information provided and if you have questions, please post back and let me know. I hope you find this information helpful.