DISH Network Televison & Video - Recent Questions, Troubleshooting & Support

Hola! mi nombre es Kimberly Escobar trabajo con DISH Network. Para programar el control remoto con su television hay ciertos codigos que se pueden integrar al control para que pueda funcionar con la television estos codigo son diferentes dependiendo de la marca de televisor que tenga. Es importante saver cual es la marca para saber que codigo se va a integrar este link puede ser de mucha ayuda aqui puede encontrar los codigos necesarios y el procedimiento a como integrarlos http://www.dishnetwork.com/SupportSection/remote-setup si tiene preguntas adicionales o necesita mas ayuda por favor contactenos directamente al 1800-333-DISH.

Hi, Mary with Dish Network Customer Service. When the picture alternately goes from normal to a black screen, it is an indication of an intermitten signal issue. You can attempt to reset the receiver box by unplugging it from the power for 10 seconds and letting it reboot. Hopefully this will resolve your issue.

It sounds as though you might have just accidentally pressed a button and changed the remote into an incorrect mode for example, tv, or aux modes. This would in fact prevent the remote from successfully working with the DISH Network receiver. If this is in fact the problem, then the remote simply needs to be put into "SAT" mode, once its back in SAT mode you will then be able to change channels, select menu, power receiver on and off, etc. The "SAT" button is labeled & in the upper left hand corner of the remote to put the remote back in satellite mode, please just press that SAT once and then release, the SAT button should briefly light up red & then the light will go out, you should then be able to use the remote again, to ensure remote was successfully changed back to SAT mode, you can press select or any other button you chose & as long as the SAT button lights up when you press another remote control button- then your all set to go & everything should be working once again! I hope this helps -please let me know if there is anything else I can help you with!
-Kirstie DISH Network

If the dish network remote control is universal it may work with limited functions. If the remote control has buttons labeled cd, receiver, cable or Aux etc. it might work. The manual will tell you for sure. It will also provide you with the proper code for the component to work.

C?DIGO para el tv TEC por favor

nmg55

Not all remote are compatible with all our receivers. Depending on the receiver and remote model numbers, if they are compatible you can readdress the remote to the receiver. I have provided a link for readdressing the remote to the receiver. I hope this helps.

Instructions on how to readdress the remote to the receiver:
http://www.dishnetwork.com/SupportSection/remote-setup
Remotes and receivers models:





222 -
21.0 IR / UHF Pro


222k - 21.0 IR / UHF Pro


301 -
3.4 IR


311 -
3.4 IR


322 -
4.4 IR / UHF Pro


381 -
6.4 IR / UHF Pro


411 -
20.0 IR


501 -
6.4 IR / UHF Pro


508 -
6.4 IR / UHF Pro


510 -
6.4 IR / UHF Pro


512 -
6.4 IR / UHF Pro


522 -
6.4 IR / UHF Pro


612 -
21.0 IR / UHF Pro


622 -
21.0 IR / UHF Pro


625 -
6.4 IR / UHF Pro


722 -
21.0 IR / UHF Pro


722k - 21.0 IR / UHF Pro







Ray Calo
DISH Network

i think this was a software issue, hopeffully its been resolved by now??

I can definitely provide some assistance and get some steps to try to fix this. To ensure I get the correct steps, how long ago did this start? Does anything come up on the screen when you try to change the channel? Was anything changed in the install? When you turn the TV off, then on, does it say an input or a channel?Tommy FaustDISH Social Media Representative

It sounds like you have interference, try removing the uhf ant from the back of rec and promgram it straight from there. you can also hookup "bunny ears or a pigtail coax to the uhf ant port to increse uhf signal. also make sure the uhf ant is standing straight up.

bennoanddash

With all receivers, depending upon the type cable going from the receiver to the TV, the TV is set either to a channel or an input setting (if using any cable other than a coax cable). I hope this helps.

Ray Calo
DISH Network

Hi there joe ibrahim, my name is Kimberly and I form part of the Social Media department with DISH. In order to disable the Inactivity Standby mode on the Hopper and Joey system, press 'Menu' on the remote, select 'Settings', then 'Diagnostics' and last, 'Updates'. From the Update Screen select Disable and be sure to select 'Save'. If you have additional questions feel free to reach me at: [email protected] EscobarSocial Media RepresentativeDISH L.L.C

that's not true i work for dish network if u have an LNB drift of -8 or +8 you can get a free lnb service call and they can come out n fix at no charge

SORRY BUT WE KNOW OF NO FIX FOR YOUR PROBLEM

This website: https://universalremote.codes/dish-network/

you need to ask the people from dish not diyer's

Contact dish to inquire. Their remote control may or may not contain the applicable code.

Hi there! My name is Kimberly and I form part of the Social Media Department with DISH. It is my pleasure to help you. Please perform a hard reset on the receiver. To do a hard reset, you simply unplug the receiver from the power outlet it is connected to, leave it unplugged for 20 seconds, then plug it back in. The receiver reboot process takes about 5 minutes. Once the show is back on, try accessing your DVR again, if it is still not working, the receiver will need to be replaced. If this is still a problem, please feel free to email me at kimberly.escobar2dish.com with your account number so we can get this resolved. Kimberly Escobar Social Media Representative DISH L.L.C

https://www.youtube.com/watch?v=iyvBW5H88ow

I had the same thing happen with my vip622 dvr, the fan ran constantly and the green light would flash...and no picture...well..I read through some things..and found out to get this receiver running correctly, you have to put it on a stand alone shelf with nothing on or around it..a milk crate underneath the table I have my TV on seems to have worked..for some reason this box can not be in an enclosed area...at all...having it sit all alone seems to be the only solution...I had to get a new HDMI cable to make it reach...but things seem to be fine now...(cross the fingers)!

Hello this is Nick Franta from DISH. There are a couple of codes you can try. The following link will provide the available codes we have. You would need to hold the SAT button down until the top 4 buttons light up, enter the code, then #. The SAT button should flash 3 times when the code is successful.

http://tech.dishnetwork.com/departmental_content/techportal/content/tech/remotes/TechRemo5.3Code.shtml

Let us know if you need further assistance!