Chevrolet Vehicle Parts & Accessories - Recent Questions, Troubleshooting & Support
WEAK SPARK AT PLUGS
That truck should have no points. It should have electronic ignition. Sounds like bad wires or bad coil(s).
Gear indicator
When you move the gear selector and the shift indicator does not move, there is a problem with the indicator. Misalignment could be a reason that can be solved with an adjustment by a trained mechanic or there may be a more serious problem.....For more info-https://www.usedengines.us/blog.php
Free engine diagram for 96 5.7 vortec
https://images.search.yahoo.com/search/images;_ylt=AwrFeFQIGjdjVukCKDqJzbkF;_ylu=c2VjA3NlYXJjaARzbGsDYnV0dG9u;_ylc=X1MDOTYwNjI4NTcEX3IDMgRmcgNtY2FmZWUEZnIyA3A6cyx2OmksbTpzYi10b3AEZ3ByaWQDWnJyN0wwVEpRSHlNOURLRnppMm95QQRuX3JzbHQDMARuX3N1Z2cDMQRvcmlnaW4DaW1hZ2VzLnNlYXJjaC55YWhvby5jb20EcG9zAzAEcHFzdHIDBHBxc3RybAMwBHFzdHJsAzMxBHF1ZXJ5A0NoZXZ5JTIwMzUwJTIwdm9ydGV4JTIwRW5naW5lJTIwRGlhZ3JhbQR0X3N0bXADMTY2NDU1NTg4NQ--?p=Chevy+350+vortex+Engine+Diagram&fr=mcafee&fr2=p%3As%2Cv%3Ai%2Cm%3Asb-top&ei=UTF-8&x=wrt&type=E211US1494G0
9/30/2022 5:18:20 PM •
Engines &...
•
Answered
on Sep 30, 2022
How to reset automatic sliding door on chevy venture van
The rear side door actuator control modules monitor the power sliding door positions at all times. Whenever the battery positive voltage supply to a rear side door actuator control module has been removed or the on-board diagnostics have been activated the power sliding door system(s) must be re-initialized. Re-initialize the right or left power sliding door systems using the following steps:
- Turn the ON/OFF switch for the power sliding door system to be re-initialized to the OFF position.
- Manually open the power sliding door completely.
- Manually close and latch the power sliding door.
- Turn the power sliding door ON/OFF switch to the ON position.
- Open the power sliding door completely using the B-pillar or overhead console OPEN/CLOSE switch.
- Close the power sliding door completely using the B-pillar or overhead console OPEN/CLOSE switch.
9/9/2022 4:43:40 AM •
Chevrolet...
•
Answered
on Sep 09, 2022
P2440 trouble code
What Does the P2440 Code Mean? Diagnostic trouble code (DTC) P2440 stands for "Secondary Air Injection System Switching Valve Stuck Open." The secondary air-injection system pumps fresh air into the exhaust system to help burn exhaust emissions as the engine warms up.Mar 1, 2022
1995 Chevy 3500 pickup 4x4 454 engine, auto
Sounds like the computer is in limp home mode.I realize you can not hook a scanner up on a 95 but you can use a paper clip to read the blinking code on the engine light. This get hard to explain here but you tube will have a video on how to read it.
1997 chevy truck 1500 neutral safety switch doesn't work
If you follow the steering column down the sw. is a half moon shaped sw inside attached to the column. Remove the wiring clip and the two screws and put on the new sw. be sure the truck is in park or set the new sw. to the position it is in now. Better to have it in park.
Had to recently replace battery. now I need the code to reset radio.
forums.carreview.com/showthread.php?1839-GM-Delco-
Radio-Lock...
Sep 29, 2005 - 25 posts - 14 authors
2000 Chevy S10 pickup, battery died, replaced, radio now locked ... Does one haveself service cheaper options to get the code and ... Note: if the display does notchange from "LOC" to "000" the unit is ... Recently I noticed that the led was flashing indicating that THEFT .... I had the same problem as you.
https://answers.yahoo.com/question/index?qid...
Feb 24, 2008 - The radio display changes to SEC Your radio is now "un-locked" and usable. ... Source(s): find unlock code chevy s10 radio: https://tr.im/o2Hg7 ... that youhad to disconnect the battery and you need the code for the radio. ... to have it reset, which could mean replacement of the microchip that stores the info.
www.automotiveforums.com > ... > Chevrolet > Aveo
Reset factory alarm on 1997 tahoe
if the security light is blinking.... turn key on try to start truck let the key go and it should leave all the dash lights on wait about 10 minutes til the security light goes off then turn the key off and then try to start the truck again repeating the process three times . no more than three. on the last time the security light goes off turn the switch off and it should start the process is called the ''10 minute relearn''.
Not finding what you are looking for?