Water Filters & Coolers - Page 7 - Answered Questions & Fixed Issues

I have the YLR2-5-96H2 and hot water stopped heating up. I unscrewed the casing and unplugged the connections to the circular heating element and 2 circular probes. Brushed off the white dust build up on the probes and it started to heat water again. I ruled out faulty heating element, because it got really hot just seconds after turning on the hot water switch.

this solution is for the whirlpool gold refrigerator remove the rear panel inside the the freezer area and see if you have any ice build up on the evaporator coil if you do you will need a multimeter and have to perform tests on the defrost thermostat which is most likely your issue the defrost heater and the defrost timer or adaptive control board. while this rear panel is off also look at if the fan is running as well. The freezer area is the only part that gets cold in a refrigerator the cold air is then blown by this small fan through a door that is located in the back of your refrigerator the door is controled by a control located ini the ceiling of the refrigerator. The door opens and closes letting the cold air into the unit as needed to achiieve the desired tempreture you can also read more on this topic by clicking here http://www.applianceoutletservice.com/appliance-care-tips/refrigerator-tips/refrigerator-defrost-system-information.htm perform your continuity tests and message me back if you have any further issues or questions and please remember to rank how this opinion has helped it allows me to continue to help others in similar situations Thanks again Rick

turn the system of unplug and turn the machine upside down without the water bottle. There shud be 2 drain plugs underneath. remove one at a time and force water or air backwards thru these drains to ensure no obstacle in pipes. Also check inside that no pipes are bent closed so as to block water from flowing thru. It doesnt work via a pump but a simple gravity feed system. also the cooling works diferent to a normal fridge, doesnt have gas in it it cools by a heating element that cools on the one side and heats on the other side. Also check that ur fan on the cooling side is still running properly it shud turn of after a couple minutes and turn on when the water gets hot again.hope it helps.regards.viv

Check the valve very common

When empty of water remove the back panel and the cooling fins are most likely covered with an inch of dirt! Find an air compressor and blow out the dirt. It worked on mine!

how do i fix and get the parts to replace the reserve tank in my Haier WDNS045 drinking water cooler dispenser

Hi,
It will work either way....it's just that the cap makes it easier to turn over and not spill
Also if you have a cap you need to have the piercing thing...

heatman101

Hello! About 2 weeks ago, the same problem began on my Hamilton Beach water dispenser.
Last week, I called the HB service support, and they told me to do the following reset procedure:

1. Dispense 3 cups from the HOT water side, and also, 3 cups from the COLD water side.
2. Turn BOTH back switches OFF (the ones on the back of the water dispenser).
3. Unplug the dispenser, and LEAVE it unplugged for 24 hours.
4. After 24 hours, turn the back switches ON and plug it in.
5. Leave it on for 4 hours WITHOUT dispensing any water.

...it's been about 12 hours since I've dispensed water again for the first time, and so far, SO GOOD! I'll update if the problems reappear.

Check power to relay. If yes, check compressor is working. If yes, keep your hand on discharge pipe. If it's not warm, cooler is under gas leak. Rectify leak and recharge gas.Thanks.

water cooler does not run or dispense water

Problem: Water is not hot

Possible Causes: Dispenser is unplugged

Solution: Push plug completely into outlet

Possible Causes: Heating switch not on

Solution: Check to be sure heating switch is turned to ON

Possible Causes: The fuse is blown/circuit

Solution: 1. Replace house fuse or reset breaker is tripped circuit breaker.

2. If too many items are plugged into a single circuit, move some items to a different circuit

Possible Causes: Temperature limiter tripped

Solution: 1. Set the hot and cold power switches to OFF

position.

2. Wait five minutes, then set switches to ON position.

3. Wait 30 minutes for water to heat or cool

Link for owners manual: http://useandcares.hamiltonbeach.com/files/840178800.pdf.

Welcome to fixya

Hello

I have a solution for this

Press Ok, Accept or replay so we may get started

Your pre-solution is coming up shortly

PLEASE REPLY OR LEAVE COMMENT TO CONFIRM YOU RECEIVED THIS EMAIL

My name is Bruce

why are the car looking at me?

i have problems with hot water, the handle is broken
YLR2-%-24H2

my hot water faucet is broken!!.. when can i get new?

Yes. Call Sears parts direct at 1-800-252-1698 or go to repairclinic.com

hot and cold water have a smel, do I have to clean or replace sonthing?

Hi,

You have got the correct information. I would recomend you to submit the part you want to be delivered in the link bellow:

http://hamiltonbeachparts.firesocker.com/hamiltonbeach4200premiumhotandcoldwaterdispenserparts/

Please get back to us if you have any further query.

Have a nice day.

call primo water corp. for parts!
866-429-7566

I need to do the same thing. Please let me know if you were able to get this done. It would help me out alot. Thanks you.