Sport & Outdoor - Others - Page 6 - Recent Questions, Troubleshooting & Support

Hi, I think that you would need to add some extra virgin olive oil to the parts that keep getting stuck. I'm guessing the friction is what's causing the different part issues. Once you apply the oil, you should see that the machine runs well. Thank you.

https://www.answers.com/Q/Where_can_you_get_instructions_for_the_ten_peaks_tent_by_quest Unfortunately, the web site given in the link above is no longer in service, so it may be difficult to find instructions other than those at the link. Quoting from the link above: ' "Ten Peaks Tent by Quest 1) Lay out the tent flat on the ground, be sure to stretch floor to eliminate slack. Drive a stake into each corner loop, then drive the remaining stakes into the side loops. 2) Install the poles by first separating them by their color code. Yellow poles make up the center section. Red poles make up the right and left sides. Slide the yellow poles through the center pole sleeve. Slide the red roof poles through the right and left pole loops of the tent. 3) Raise the tent. Assemble the yellow upright poles and attach them to the yellow roof poles. Raise the center of the tent to its approximate height, by using the quick clamps on the bottom of the yellow center uprights. Assemble the red left and right support poles, attach the support poles to the roof poles. Place the side support poles on the ground near the side stake loops. Adjust the placement and the height of the poles until the tent stands firm.

For others, not the OP from ten years ago: Search Amazon "JR Products 97025 Chrome Manual Water Faucet" and this might be the same mechanism and parts as your Coleman 2231 pump. I went to my local shop in Calgary (starts with an H and ends with obo's, fixya considers that word to be profanity so I can't use the name H*bo's) and they had them there for $39. I swapped the plunger, cork and cylinder from the new one into my Coleman 2231 and will keep the bits from the new one for possibly the other parts in it.

Question moved from MISC. I live in Toronto! Try removing the key and reinsert it. The KETTLER treadmill has an emergency stop mechanism for your safety. Before starting your workout, fasten the cord of the safety key to your clothing. If the treadmill has been shut down by removing the safety key, restart it by reinserting the key. An automatic restart of the treadmill belt does not occur. Further instructions concerning the handling of the safety cut-out can be found in the operating instructions for the training computer. https://manuall.co.uk/kettler-toronto-treadmill/ ..

Still looking? I have a original instruction sheet I can send you a copy! [email protected]

This is an old thread, but the best google result. Found these inside the tent - after I spent ages looking for them online.

You can usually search data bases, like https://klipperusa.com/pages/racquet-stringing-patterns. If you are familiar with stringing terminology. If you have been stringing tennis rackets as long as I have (+20 yrs). You can figure it out without stringing patterns.As for the string pattern found on the Klippermate website.Tension 55 - 65, String length 20'M - 18'C, Pattern 16M X 19C, Skip M Holes 7,9T - 7,9B,Tie off M 6B, Start C 7T, Tie off C 5T - 11B

Generic videos on Chinese scooters in the link. https://www.google.com/search?q=Replace+battery+on+a+2009+150+cc+benzhou+scooter ..

If you're talking about walls or trim just measure each wall, then add them up. 840 liner feet is 840.

Videos in the link. All Chinese scooters are the same. https://www.google.com/search?q=change+brake+fluid+on+Tao+Tao+ATM+50A1 ..

Question edited for clarity. There is nothing specific to this tent, but all dome tents operate the same. Insert the poles, peg out the base. There are videos in the link. https://www.google.com/search?q=Insta+set+Santa+Cruz+Dome+tent ..

Contact the manufacturer/distributor directly to request the instructions.

Timberland or TimberLINE? Timberland make boots don't they? Dome tents normally use fibreglass poles that fit in a sleeve. Measure the length of the sleeve. Or ask here https://eurekacamping.johnsonoutdoors.com/accessories/repair-kits-poles/timberline%C2%AE-fly-rod-replacement-pole https://www.google.com/search?q=timberline+14+man+dome+tent+replacement+poles ..

Question edited for clarity and spelling 'oal', unless you meant 'Overall Length', in which case it need to be capitalised. 72", 60" or 54" backboard Details in the link. https://www.google.com/search?q=Spaulding+portable+basketball+goal ...

Have you tried the Sevylor repair kit?

you cant repair a gas shock. replace it

The same thing happened to my kids rods.
A friend suggested a product called Bobber Stopper.
It's basically a small bead and string. I found that the bead would not
reel back in, but if you just tie a piece of sting on the line big enough
so it does not fit through the bobber. It worked for me, so hopefully
this will work for you.

I am sure there is one to download but did not found anything with google...
If search engines are no help, just ask some deep web specialists, e.g. http://manualfox.com - this is a manual search agency and if they don´t find it, it does not exist in the Internet.

ebay

this is it