Science & Laboratory - Page 9 - Answered Questions & Fixed Issues

It sounds like the backlight of the LCD display is out. The Image is still being displayed there is just no light to illuminate the image. Try shining a flashlight on it (Put the light right against the screen) and see if you can see what's on the screen. The display is fairly easy to install but I do not know where you can purchase one directly.

Your question is hard to answer without more detail, including movement rate and required magnification. For relatively slow moving objects you can use a movable stage (X-Y stepper motors tied to a computer). Usually the direction of motion is erratic or unknown, and some digital tracking software will have to be written to drive the steppers so as to follow the designated object of interest. This may be something you have to develop yourself, although there may be some "tracking" software commercially available (or adaptable). Note that you usually cannot take a video of the object as you track it, due to the quantum action of the stepper motors. However, this does not keep you from taking a series of stills (step - capture - step - capture - step ... etc.) and turning them back into a stop-action video. There are a lot of free or cheap programs out there to do that. If the motion of the object is rapid, then you have a much bigger problem. One project I did some years back had this problem, and we could not actively track the sudden motion with a microscope. What we did instead was to reduce the microscope magnification, and significantly up the resolution of the high-speed camera (and yes, that was very expensive). At 1500 FPS, we could capture the object as it moved rapidly across the stage, then post-process the resulting frames to center on the object. The obvious limit here is that the object needs to cover a relatively small portion of the overall picture - which limits the magnification you can use. Of course, the offsetting advantage of this method is that you pay more for the camera, but don't have to have a movable stage on the scope.

hi im not sure but is his it? http://www.mvi-inc.com/wp-content/uploads/D-FL_EpiFL-Attachment.pdf

Hi Could you send user manual of dynatech microplate reader mr700 to me please? Regards

If you're clever with electronics and can solder, consider an LED replacement. Do you have any data on the voltage, current, or lumen rating of the bulb?

Saturn.. The first five are Mercury, Venus, Earth, Mars, Jupiter.

Hello, Do you still need it?

je cherche une notice du spectrophotom?tre Hitachi U2001 en Fran?ais. j'ai une panne sur cet appareil et souhaite faire un premier diagnostique. Merci

There is a faulty capacitor on the bottom of the drive PCB, replace it (800nF 1000v) along with the drive PCB input fuse (3 amp)

SADLY Stryker seems to use their service and "manuals " sections to FURTHER ADVERTISE their EQUIPMENT... I was hoping to find, 10W oil, dextron... etc... (but alas.. I found NOTHING (sorry)). Contact them directly at Phone: 800-STRYKER (787-9537) Option 1 for Field Service Option 2 for Tech Support Fax: 866-787-9095 Email: [email protected]

Error E3 on my de humidifier kenmore 129-25805

Did you ever get an answer. I, too need a pin-out of J6 to connect to a chromatography data system. Thank you

Volcanic gas Wikipedia

its a old post , but if you need one speak to ukmicroscopy.co.uk they will have a digital one for the 1512. How ever if you need any advice on how to use it contact me back via this forum

Hi , Do you want to sell the this microscope? Kind regards , M

Here's the operation manual up to section 5.2: http://www2.park.se/~olle/KeB/LKB%20USII.pdf

Are you an inspector of any spirit distillery? Seems so. Brand, Rum or Wine? Products? Be frank with your questions.

I will on but still standby

We are having the same problem and my understanding is, we can not adjust it. It needs to be set before it is delivered and once delivered can not be reset unless it is sent back. We have had a repairman come out to fix a loose wire on our new fridge and he tried to contact aegis customer support but was unable to reach a live person in that department. Still waiting ....

Timing too advanced.