Refrigerators - Page 4 - Recent Questions, Troubleshooting & Support
I can't get my ice maker water filter to turn and lock in place
Put some Vaseline on the O-Ring to help it slide into place. Make sure it is properly inserted at the beginning.
If the filter is located inside the refrigerator:
- Turn off the ice maker.
- Push the eject button.
- Pull the filter out of the housing.
- Push the new filter into the housing until it clicks.
- Turn on the ice maker.
- Run 2 gallons of water through the water dispenser to purge air and residue.
More items...
•
Aug 30, 2023
1/28/2024 2:40:53 AM •
Kenmore...
•
Answered
on Jan 28, 2024
Defy fridge f640 replacing door hinges
Hi, the defrost element of our defy double door fridge is tripping our electricity. Are there any certified defy technicians in the garden route, specifically the George, Sedgefield area?
Contractor's Assistant: What's https://waltonbd.com/refrigerator-freezer/freezer and model of your fridge? How old is it?
Defy double door model F640 and it is about 15 years old
Contractor's Assistant: How long has this been going on with your refrigerator? What have you tried so far?
For about a month. Just before Christmas. We have had an appliance technician here and he said it's probably 99% the defrost element. He checked everything else, the plug the gas etc. Those were all in order.
Kenwood American fridge freezer not working, yet fans are going?
Much depends in the unknown MODEL number, but it will either be lack of refrigerant gas or the freezer evaporator is frozen over because the defrost timer or defrost heater has failed.
The internal fans just circulate the air. The more important one is the one on the condenser, but you don't say which fan is running?
..
Fans in both refrigerator and freezer of Samsung RF4287 HARS-xaa are not working. Replaced evaporator fan motor in fridge and it is still not working. Help, please!
could be just the coil on the valve, but most more likely valve getting stuck as it opens. somtimes can take apart and clean, will work for awhile, but if have the cash best just swap it out. will save you hassel down the road.My Aplogies I was under the impression you had already located the valve. I as I have not seen unit I can not give the location, However since it is on the water system, I would trace water tubing from where it connects to unit. It should not be far from inlet connection. Look for tubing going to a valve with wires ontop, ensure after the valve is where you whish water/ice to come out. Once that is located take photo and order new valve, or secure water remove and clean valve. Note have container ready as water will leak once you remove valve.
1/25/2024 4:41:01 PM •
Samsung...
•
Answered
on Jan 25, 2024
Our Samsung refrigerator model RFG297ACRS is not cooling and freezer not cold.
First I would clean all grim. Second if you do not have refrigerant gauges feel discharge line with hand. Will be a smaller line and coverd with foam. It should be hot to condensor. if not You probabaly lost charge. Also top of compressor should be hot. Should the above not meet specs. You need to find leak, get a pro. to locate repair leak, as you need licenese to go further.
1/24/2024 9:51:02 PM •
Samsung...
•
Answered
on Jan 24, 2024
Evaporator fan new but not working on samsung rs267lash
Manny MANY unfortunate customers who bought this **** from Samsung have problem.
Specifically the Freezer cold but fridge side no lower than 55deg problem.
It is a known defect that Samsung has not taken ownership
of.
I have the same problem with the same model as many.. if you search the
net.
Iv'e been trying to find a designated website for repairs for this
problem. Please post website with solution if anyone finds it.
Thanks
1/24/2024 8:45:56 PM •
Samsung...
•
Answered
on Jan 24, 2024
Polar g 620 ice machine ice full light blinking machine stopped working
I have not worked on your polar machines, but many manitowoc machines, I have found that the switch sticks it is most often on the upper left if cube unit. If crushed Ice is the top. Either way try to change switch state either open or closed. Once you have that you can go further. Get new switch of clean it (which is most often the case.)
How do you open bottom of dryer to clean out dust
The "toe panel" is held in by spring clips near top corners. See item 46 in parts diagram attached.
Carefully pry the panel outward. Use an automobile panel pry tool or possibly a screwdriver wrapped in tape.
Not finding what you are looking for?