Audio Players & Recorders - Page 7 - Recent Questions, Troubleshooting & Support

Question edited for clarity, turned around plus CAPS. It should be a standard figure 8 connector. https://www.google.com/search?q=sony+audio+rack+su-s5520+power+cord+replacement ..

I have the mesures (in cm) of each one. See the picture. You'll need 2 pairs (1 pair for each engine). *esticada = stretched; espessura = thickness

CD/DVD players use a protocol; Open tray. Insert disk. Tray switch tells mechacon that the tray is shut. Attempt to focus on disk. If focus is acheived, then it will spin up and try to read the disk otherwise it will ask for a readable disk. If the tray keeps opening, I would suspect the tray detect switch is malfunctioning, maybe the drive belt has stretched.

Download any video converter, its easily found on google. after downloading your movies, drag them into your any video converter on the top right hand side of the any video converter change profile to Customized MP4 movie, under that they'll be video options, i use as follows an it works perfectly,
Video Codec: Xvid
Video Size: 320x240
Video Bitrate: 768
Video Framerate: Auto
Audio Options,
Audio Codec: aac
Audio Bitrate: 128
Sample Rate: 4410
Audio Channel: 2
Disable Audio: No
A/V Sync: Default, be careful when downloading Any video converter, sometimes when you download it it only lets you convert 3 minutes of it try downloading fron a differtent site it completely free!!! and for the best Movie downloads for free go to www.pspiso.com sign up then go down to PSP format movies then movies, then scroll down and pick any of the uploaders, then go to the last page there will be a list of movies good Luck :) email me if theres any problems ill be glad to help :) [email protected]

Music downloads are subject to copyright and not allowed in a lot of cases without payment.

This appears to be a South African unit? See if the link works better for you. An electronics technician could fix by component testing and by knowing how to wire a transformer (high voltage windings and low voltage windings). https://www.google.com/search?q=dixon+power+mixer+tms+8+wiring+diagram ..

Rubbing as in its grinding or just a like its in motion its normal to hear some type of rubbing as the platter spins because if u notice when u push down on the platter it has some play you can clean the inside by removig the platter and cleaning and dirt and dust

I would remove the potentiometer and note te maker and value plus the size. then look on Mouser, RS Components or another supplier and source a suitable replacement.

Question edited for clarity. It you have standby, that shows you have power. The only things you can try is a Power Reset, disconnect from the mains, for 10 minutes. Press and hold the power button for 60 seconds and then plug back in. If you are using a remote, check the batteries in the remote. You can also do the check to make sure the remote is putting out a signal. Aim the remote at the front facing selfie of a smartphone. You should see a flash. No one else has reported your issue. https://www.google.com/search?q=Philips+fr-968+radio+receiver+no+sound+or+display ..

All devices that have a remote need a remote https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote ..

One of the channels is blown and unit goes to protection mode.

The E display indicates disc loading error.Due to inactivity the carousel loading trays rubber belt would have either become stiff or loose ( depending on which part of the world you live in ).So your loading action is not being completed due to your loose loading belt condition.
There are sensors ( small leaf switches ) which tell the micro controller if the tray has gone in completely and lifted the CD off the carousel tray, only after that the CD starts spinning for play operation. If this sequence does not complete the tray opens and closes by itself in some makes and model during power On
If you are up to it you can open the top cover and see the loading tray and beneath it is the loading belt.Your challenge is getting a replacement today of an old model.

The OP Solves the issue. Hey there!!! I fixed my own problem. Can't or shouldn't plug into the same outlet as the rest of the audio equipment. Moved the plugs around and.....BINGO!!! No more humming!! Well done.

This information may differ depending on the manufacturer, model, and version of the product. It is critical that any replacement part you select is compatible with your specific model of subwoofer and meets the electrical standards. Making changes to electrical components such as transformers can be dangerous if done incorrectly, and it may also void the product's warranty.

• I recommend contacting the manufacturer or an authorized repair center for assistance in locating a compatible replacement transformer and instructions on any necessary installation procedures. They will be able to give you the most accurate and safe answer for your particular situation.

The 0-83 error indicates a problem with the firmware update. Try resetting the receiver's BIOS by following these steps2: Unplug all cables Un-Power the receiver Power the receiver Before the receiver gets into the "Enter for updating" message, press Tone + CBL/SAT + ON/STANDBY. This will show you either the volume numbers or get you into settings of the receiver's speaker configuration. Press CBL/SAT + ON/STANDBY. This will clear the BIOS and show a "Clear" message on the display. Wait until you hear a couple of clicking sounds for the receiver to turn on and off the power. TX-NR555 Owner's Manual - Onkyo Product Support (onkyousa.com)

Windows Media Player Invalid File Format Error Message

https://support.microsoft.com/en-us/kb/234019 Microsoft CorporationWindows Media Player does not support the file format or the codec of the media ... currently, but does provide support for the most common types of media files.

Invalid File Format - Microsoft Support

https://support.microsoft.com/en-us/kb/842183 Microsoft CorporationThis problem may occur if any one or more of the following conditions is true: Some of ... If Windows Media Player does not support the file format that you are using, contact the ... Microsoft supports MPEG4v3 files in .asf streaming format only.

Cannot play back the file. The format is not supported. (Error

You have a fault in the power amp. Identify the faulty channel by following the input leads. As, a stereo amp is basically two mono amps put together. You can compare the bad channel with the good one. First thing to do is a visual look around. If you see something odd looking in one channel and it's the faulty one, compared with the good channel, you might have found the cause. Look at the devices or device on the heatsink especially. If nothing stands out, the next thing to do is test the channels. You can do this in two ways. First, by touching the parts on each channel (with power on) with an insulated screwdriver. If you get a buzz in one channel and nothing in the bad one, in the same places of course! You might have located the faulty device. You can do the same with a volt meter. The readings should be the same in each channel. Work forward from the end of the preamp stage. Don't bother with the power supply parts, as they are common to both channels. By the way, don't short anything!

Try disconnecting all of the speakers except the left and right main speakers. If it works, check the wiring at the back of each speaker to make sure there aren't any shorts between the terminals. Better yet, just inspect the terminals both at the audio unit and the backs of the speakers. Stray strands of wire reaching across to the other terminal or exposed wire on the other side are a common problem. If you have that all cleaned up and still have the error, you may have shorted transistors in the output amp of one of the channels, very likely the subwoofer. This may be caused by shorted speaker wiring, or the amp may have failed on its own. In either case, you would have to replace both of the output transistors for that channel (they may be built into a power amp module, in which case the module must be replaced). This requires soldering skill, and the knowledge to identify the transistors and check them with an ohmmeter. Most of the time, it's a basic job for any skilled electronic technician. (I did run into one model that would have required two days of disassembly labor just to get at the failed transistors - I told the customer that wasn't designed for service and he would be better off buying something different to replace it.)

The Denon DRA-697CI stereo receiver typically uses a 250V, 2.5A fuse. However, it's always a good idea to consult the user manual or check the label near the power input on the device itself to confirm the exact fuse size and specifications for your particular model. Using the correct fuse size is important for safety and to prevent damage to the receiver. If you're unsure, you can also contact Denon customer support for assistance.

The Denon DRA-697CI is a stereo receiver. Typically, the fuse size for electronic devices like stereo receivers is listed in the device's manual or on a label near the power input. It's important to use the correct fuse size to ensure proper protection against electrical faults. Without specific information about the fuse size for the Denon DRA-697CI, I recommend consulting the device's manual or contacting Denon's customer support for accurate information. Using the wrong fuse size can potentially damage the device or pose a safety hazard, so it's crucial to verify the correct specifications.