Garden - Recent Questions, Troubleshooting & Support


The intake valve is the lower valve and its push rod is the aluminum one, the exhaust is the upper valve and it has the steel rod, there is no rocket science going on here, the aluminum push rod is used to cut costs.

Parks Optical... | Answered 12 hours ago


Not much info here... I would take it to a professional and pay them to adjust it correctly..

Garden | Answered Yesterday


Hello, rebuilding a starter is not hard... First.. disconnect the battery!! Tie back the connector! There should be one heavy wire going to the starter.. remove it.. tie it back out of the way..There might be 2...or 3.. or 4 bolts/nuts holding the starter on, once they are removed you can remove the starter..DO NOT tap on the round outside housing!! Get a couple clean rags on your work bench.. the starter will have 2/3 long bolts -- or short bolts/nuts/screws on each end.. -CAREFULLY NOTE HOW IT COMES APART- ..remove these...once you have removed each end.. the armature is heavy and the stator is magnetized..remove the armature .. watch for falling shims/washers that belong on the shaft and make sure they go back in the same way!! Now its time to inspect the armature/commutator for wear or damage.. you need to turn/mill/machine the brush's contact area on the commutator to give the new brushes full contact (and, now, this properly done rebuild will last a long time!!).. once the area is flat, smooth, clean and de-burred you need to make sure the MICA UNDERCUT is correct..the "plastic looking" area between each of the little commutator lands must cleaned out/lightly scraped out so there is NO CHANCE the brushes will contact the undercut area! Once this is done correctly,, you will have a nice clean and freshly surfaced commutator! Make sure the bearings are free/bushings are clean, make sure the shims/washers are in place and reinstall the armature..The new brushes come as an assembly (easiest way) or two/four brushes to be installed in the old plate..(yuk)..you have to ma ke sure the brushes are pulled back/locked out of the way.. sometimes you can just move the spring off the brushes and that work great..another way to lock the "out' is with a bobby-pin/hair pin folded into a locking "spring". Once you have the armature/washers/shims/brush plate correctly assembled its time to put the bolts/nuts together and SLOWLY tight everything.. If you have done this correctly the armature should have a noticeable "rumble/feel the magnets working" when turning it by hand..thats the magnets doing their job..Check the armature shaft for excessive and play (did you leave out any shims or washers?).. if it feels right... just re-install in reverse of disassembly.Good Luck!
IF YOU CANNOT DO ALL THIS..just take the starter to a shop that you trust... Now its almost as cheap and easy just to buy a lifetime warranty one from a major auto store.

Garden | Answered Yesterday


Dash lights flashing on my 5205

Garden | Answered 3 days ago


Air trapped in the fuel filter is normal. Air bubbles in a fuel line would imply a cracked fuel line.

Garden | Answered 3 days ago


Numerous women question how they could shrink fibroids naturally in the estimate to either steer clear of surgery or to fibroids home treatment cozy by themselves.

Stihl Garden | Answered on Dec 05, 2019


SORRY YOU HAVE TO DO THE SEARCHING FOR YOURSELF WE KNOW OF NOTHING LIKE WHAT YOU ASK BUT USUALLY HAVE TO DRILL THE BROKEN BOLT OUT I WOULD USE LEFT HAND DRILL BIT .WWW.HARBORFREIGHT.COM SELLS THEM

Stihl Garden | Answered on Dec 04, 2019


it needs fuel.

Toro Garden | Answered on Dec 04, 2019


Likely the recoil starter is kaput. Removing spark plug so there's no compression, then pull starter. If it's still hard pull, remove recoil starter assembly and spin engine by hand. If engine spins freely, replace recoil start.

Garden | Answered on Dec 04, 2019


NO....... YOU WILL NOT USE THIS
25961692-wzeblxvamairr1ekd2ambqox-5-0.jpg

But you will use maybe this a bearing separator .










25961692-wzeblxvamairr1ekd2ambqox-5-1.jpg

Ryobi Garden | Answered on Dec 04, 2019


Precisely yes, they were grown in the open fields, dont know if they were along I-80 tho.

You can get more info here probably: http://expertplantman.com/

Garden | Answered on Dec 03, 2019


https://partscatalog.deere.com/jdrc/sidebyside/equipment/70454/referrer/navigation/pgId/2397003

Familiarize yourself with fender deck footrest attachment points.

You have to remove the seat and the fender deck footrest. Pedals, cut height adjuster knob and whatever else.

Garden | Answered on Dec 03, 2019

Not finding what you are looking for?
Garden Logo

192,762 questions posted

Ask a Question

Usually answered in minutes!

Top Garden Experts

roeb

Level 3 Expert

819 Answers

john h

Level 3 Expert

22486 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...