Food Mixers - Page 6 - Recent Questions, Troubleshooting & Support

Question edited for clarity. Question moved to category. The speed lever is electronic. Videos and the part in the link. https://www.google.com/search?q=Kitchenaid+Professional+6+mixer+speed+lever+stuck ..

HI Joe
I have the wrong greace in my A200 standmixer i need to know what kind and how much to put in gear cace. thank you

Try having the planetary nut(s) less tight. From what I've read this model is very sensitive to the main shaft being tightened too much. I'm in the process of rebuilding mine and I screwed this up. Sounds like you did better if it's largely working. Let us know what you find.

Unfortunately not available anywhere online. Check eBay once every couple of weeks. https://www.google.com/search?q=Cooks+sm248+manual ..

Reset Malfunction is 6 Blinks. https://www.google.com/search?q=Hobart+Grinder+Mixer+blink+6+times MANUAL

mg1532 mixer-grinder (208-240/60/3) technical manual

https://img.sigmaequipment.com > equipment-docs PDF The exclusive Hobart designed #46 Wedge cylinder grinding end speeds product from hopper to grinding end by pulling pieces of meat through the large upper. 50 pages

Help in the link including from Kenwood themselves. It is likely to be the selector, the control board or the motor. Take it in for Dealer Service. https://www.google.com/search?q=Kenwood+kmix+doesn%27t+start ..

Question edited for clarity. https://www.techtownforum.com/forums/discussion/deciphering-hobart-serial-number/ and https://www.google.com/search?q=hobart+mixer+age+by+serial+number ..

I had this same problem as well.  The beater was stuck like glue to the rotating arm, and it would not budge with any amount of pressure.  I tried the cooking spray and it did nothing.  But today I put a rag in hot/boiling water and then carefully wrapped it around the top of the beater.  I let it sit for 10 minutes. Then I put the rag in hot water again and repeated the process for about another 5 minutes.  When this was done, I covered the beater in a towel (to protect it) and forcefully tapped (ok... I pounded) it with the flat side of my meat tenderizer (it was all I had...you could use a mallet or hammer).  It took a little bit of work because I had to hammer it from the bottom, then the side, then the top to get the little spoke guided through the shaft.  But it did finally come off.  After cleaning with hot water, I put the beater on again and noticed that it was still a little hard to get on/off.  So, I put a little bit of veg. oil on it, and it seems to be better.  Going forward, I will be sure to clean the top of the beater & arm after each use and then coat it with a little oil to keep from sticking.  Best of luck!

Question edited for full 'make model (what it is)'. There must be a spring in the base that helps the top rise when you depress the button. You will need to remove the base. The manual doesn't mention anything and there is no Service Manual https://www.manualslib.com/manual/1021018/Hamilton-Beach-63390.html?page=5#manual Very limited help here apart from JustAnswer dot com https://www.google.com/search?q=hamilton+beach+model+63390+mixer+tilt+button+not+working ..

Hello.

first press the boton green inside of the machine, when up the head.
if not working .
then is problems the capacitors and resistors.

Regards
Kenwood Chef Restore

Hi, apply some cooking oil to where the parts are connected. If that fails, please submerge the parts in a bucket of or tube of water and attempt to detach them from each other. If all else fails, please reference the manual to ensure that you've not missed a detachment procedure. Thank you.

Hi, Please double check that you're not inserting the bowl backwards. If this is not the case, you might have to disassemble and then reassemble your machine prior to attempting to insert the bowl again. Also, you might add some oil to the glass bowl to help it slide under the plastic stand holders. Thank you.

Hi, The mixer looks to be an antique so you might start with Ebay to find that specific mixer part. Thank you.

Hi, Please reach out to sellers on Ebay and Amazon that sell your brand of product and request the beaters for your mixer. You can also call your local Target to see if they have the beaters in stock. Thank you.

I have answered your question Rosa. The question you resurrected from the dead is from January 2013!!

The sparks are generally seen where the carbon brushes meet the copper commutator on the motor spindle. This is actually fairly normal. You can lessen it by spraying with some light machine oil, but eventually you will need to replace the carbon brushes.

Impossible to guess what make and model you have! Google make model replacement beater https://www.google.com/search?q=Moulinex+model+replacement+beater ..

There is help here https://www.fixya.com/support/t20938419-hobart_m802_mixer_bowl_will_not I would just call for Hobart service https://www.google.com/search?q=hobart+m802+bowl+lift+not+working ..

Hi, If you call the glue manufacturers, they might be able to direct you to a substance that can dissolve the glue that was applied. Thank you.

That should just lift off, I'm not familiar with your particular model but all the bevel gears I have seen just drop onto a pin that is just a push fit through a hole in the shaft.