Juicers - Page 2 - Answered Questions & Fixed Issues
How to take the blade off on the hl 2051 juicer
Yes for the PHILIPS HL-2051 juicer the screen comes off very easily if you know how to do it as I figured it out without the manual. My method works 100% guaranteed. What you do is unplug the cord from power receptacle. Take the whole PHILIPS JUICER unit/contraption and put it between both of your knees/legs to support it without your hands. You then use both free hands to pull on the loose fitting housing which collects the juice and VOILA the top loose housing and the screen comes of very easily because it is only a friction fit tightness that the screen sits on the base motor. It is then very easy to put back on again after cleaning.
11/2/2021 9:01:24 PM •
Philips Juicers
•
Answered
on Nov 02, 2021
•
970 views
Darn thing STILL won't turn on
There is a little knob on pulp collector that pushes in a switch, probably to assure the unit is assembled before operation. Mine broke off. I opened bottom of unit and used electrical tape to permanently engage the switch. The Juicer now works. I consider it poor construction that such an important part of the operation of the unit is able to break off and poor customer relations that there is no help for this on their web site. I have used it only a handful of times and the unit has mostly been in storage and has not been abused.
6/5/2021 11:32:21 AM •
Jack Lalanne...
•
Answered
on Jun 05, 2021
•
11,052 views
Hi, my Breville Fountain model JE95XL does not
if you can tear apart look inside bottom screws look at motor if brushes did not just smoke and or check if does have power to motor when on be careful ...8-10 times most it died because of too much heat of the fuse link size of a asprin pill when it gets up to , thet call it a thermal fuse one over heated it blows and you throw away i dont i fix.SF139E-142 Degree Thermal Cutoff Fuse 110-250V Instant .look up google to see pic .electronics store sell them or online i would mention radio shack but all on line mow a days ..good luck >^.^<
5/12/2021 1:31:59 AM •
Juicers
•
Answered
on May 12, 2021
•
197 views
Dull cutting wheel on Acme Supreme Juicerator
WARING AT 800 492 7464 OR COST PLUS
JUICERS AT 800 578 5939. ABOUT $30. IF
YOU ARE HANDY YOU CAN SHARPEN WITH
AN ELECTRIC DRILL AND SMALL BIT. DRILL
VERTICALLY IN TO EACH CUTTING CREVICE.
5/8/2021 11:04:04 AM •
Acme Juicers
•
Answered
on May 08, 2021
•
208 views
My lid doesn't seem to fit properly. When I put
Is this a new cover? There is an adjustment. On the bottom of the machine, dead center,
there is an adjustment screw with a locking nut. Unlock the nut and the turn the screw
counter clockwise, this will lower the motor shaft and consequently the blade. Once you
have clearance and install the cover, turn the screw clockwise until the blade contacts the
chute, back it off a half turn and lock her down. This will establish the correct gap between
the chute and blade. Also if your chute is ever chipped or scored by the blade because
of excessive vibration, you can file the chute level and readjust the gap.
Hi I have an older acme supreme juicerator, model
Believe the basket is the same. The newer lids have a flange
around them which can be filed down. Takes time, but file away
tapering it until it fits in the juice bowl. With a new lid you may
have to adjust the chute to blade gap. On bottom loosen center
locking nut and turn adjusting screw clockwise until chute contacts
blade, then back it off a half turn and lock it down. A few older lids
are around, but it's hit and miss.
Having trouble getting lid to lock into place
I just got one of these from my dad and last night I proceded o clean it.I took all three of the loose parts off and they are now soaking.
But the middle base part took a little figuring out.
This morning I finally got it.
The center part that you are referring to locks down tight I am assuming so there are no leaks.
What I found to do was that when putting the base back in I had to posistion the spout to the left as far over as I could get it and push down hard. Once it was flesh with the unit while still pushing it, I then turned it to lock it in place.
Hope this helps.
My omega 8003 juicer will not power on
1. test for power at female end of cord? (eliminates, breaker, socket, cord, plugs, all wiring to appliance. I think this appliance is hard wired at the connection, so you may need a non-contact tester.
12/9/2020 6:01:09 PM •
Omega Juicers
•
Answered
on Dec 09, 2020
•
216 views
Not finding what you are looking for?