Building Materials - Page 7 - Recent Questions, Troubleshooting & Support


notify manufacturer or locksmith

Building... | Answered on Jun 06, 2019


Hello, Debbie -

I hope you have the user manual for your garage door opener so you can check it to find out what the beeping sound means. If you don't have the manual, you can add the name of the garage door opener manufacturer to your question by using the Edit feature, so that I or someone else can look up information specific to that particular make of garage door opener.

Many instructions I have found for a variety of makes of garage door openers state that the beeping can mean the back up battery for the garage door opener needs replacing. See the information here:
https://www.garagedoorrepairco.com/garage-door-blog/garage-door-opener-beeping-replace-backup-battery

Building... | Answered on Jun 03, 2019


Google (Mastercraft)(manual) without parens.

Building... | Answered on Jun 03, 2019


Locksmith may help, or law enforcement if an emergency.

AAA in the United States includes locksmith service by calling the AAA number.

Building... | Answered on Jun 02, 2019


Since you did not specify make or model, replace button, check wires to button. The are plenty of guides on line. Google your question.

Building... | Answered on May 30, 2019


Here is a rather silly video that could assist you, although it isn't actually for your actual door, all such doors have a similar set-up.
http://precisiondoor.net/videos/program-liftmaster-remote

Building... | Answered on May 29, 2019


I am not aware of any manet thing on a garage door opener so you are going to have to give some more information.

Building... | Answered on May 29, 2019


I had the same problem. Although it appeared to be the logic board, on mine it actually was the connectors between the logic board and the power supply board.
There are 2 connections on the logic board. One white connector with wires going to the main unit, and another set of connectors that plug directly into the smaller circuit board that holds the step-down transformer (120vac - 22vac). These pins were not making good connection between the boards. I simply bent the pins slightly so they would make better contact on the logic board and have not had a problem since. This must be a weak point on these door openers. Purchasing a new logic board would work too, as the connectors are newer and tighter.

Sears Craftsman... | Answered on May 28, 2019


The opener you've have cannot be retrofitted with sensors. The control board inside opener is not designed to use one. If you go to Home depot Chamberlain openers start at $128.00 is similar to yours includes may upgrades, including Security+2.0 technology,. This does not use DIP switches which are not secure.

Building... | Answered on May 28, 2019


contact the makers. there are too many kinds

Building... | Answered on May 27, 2019


If you're having to hold that inside button down to bring it down that is because of your sensors being out of alignment. On the bottom left and bottom right of your garage door track are your photo eyes and if they're not cleaned and pointing toward each other, then they will not allow the door to close. It will only close with the inside button because it is hardwired and when you hold the button down it shoots a continuous current that bypasses Those sensors. Remotes and keypad are wireless and must have photo sensors aligned to work

Building... | Answered on May 25, 2019


Unplug the unit for 1 minute, pug in again and retry.

Building... | Answered on May 23, 2019


You can google the question:for answers.
How do I engage my Raynor garage door opener after I pulled rope to disengage it
About 34,700 results (0.78 seconds)

Building... | Answered on May 23, 2019


The original Legacy opener came out with a static 390 mhz frequency radio receiver that utilizes 12 security dip switch settings. The model number of the Legacy openers are shown as 496 or 696. You will be able to locate 12 little switches inside an existing remote control or on the backside of the garage door opener motor.
That opener remote will not work. You will have to call Overhead door, or replace GDO with upgraded security and home link to use opener in car overhead. Step 2 lists openers that the glicker will work with.
https://www.overheaddooronline.com/blog/bid/125445/What-remote-control-works-with-my-Overhead-Door-Legacy-opener

Building... | Answered on May 18, 2019


You need to go on line to see what series you have. There are several different radio units under the same model number.

Building... | Answered on May 15, 2019

Not finding what you are looking for?
Building Materials Logo

4,034 questions posted

Ask a Question

Usually answered in minutes!

Top Building Materials Experts

Tom Chichester

Level 3 Expert

55370 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

ray gallant

Level 3 Expert

66169 Answers

Are you a Building Material Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...