Blenders - Page 7 - Recent Questions, Troubleshooting & Support


THEY WILL IF YOU NEVER USE IT .

Blenders | Answered on Feb 09, 2019


are talking the blade inside the canister if so it unscrews from the clear handle and view area. otherwise if you mean the chuck below when the canister is lifted off that is held on by a fastener right in the middle dead center

Russell Hobbs... | Answered on Feb 08, 2019


sadly we can not help you find one , check with manufacturer or look for a rubber stopper at local home improvement store

Blenders | Answered on Feb 07, 2019


Check the black driving clutch on the top of the motor that engages with the other clutch half on the base of the blender jug. The fault should be there, normally it will be the motor part.

Vitamix Blenders | Answered on Feb 03, 2019


There's not enough detail to help solve your issue. Can you please post the brand name and model number?

Blenders | Answered on Feb 02, 2019


Call 1-888-367-7373
Business Hours: Mon - Fri 10:00am - 5:00pm EST

Or email: help@myproduct.care

Blenders | Answered on Feb 02, 2019


Yes, I know what it is. On the base of the blender jar (the plastic base) there are some "fingers" that must contact the base to allow operation to take place. Turn it upside down and look at the little plastic "fingers" around the outside periphery of the plastic base.

These fingers tend to break over time... mine only has two left right now, and it only works in one particular position as a result.

Rotate the blender jar one spot at a time until you are able to operate it "normally". I use it for margaritas, and it won't allow me to push the button for Frozen Drink unless the jar is in the right position.

I am going to try and find a replacement base (or entire blender jar) somewhere... or else I will finally have to retire my favorite blender of all time!

Oster 6700 Work... | Answered on Feb 01, 2019


-Try each one that come with . So You will know which one is the best for it.

Good luck


Mai

Bamix Blenders | Answered on Jan 27, 2019


GE would be a possible source.

GE Blenders | Answered on Jan 23, 2019


I just had the same problem too and ordered the fuse online with the link above. Thanks lele44!

The four feet on the bottom are easily removed with a 1/4" socket slipped inside the each rubber foot fitting.

I'm glad I found you. I saw some downright horrible reviews of my local Oster appliance service center here:
http://www.insiderpages.com/b/3723327730

Rob

Oster 4134 /... | Answered on Jan 21, 2019


SORRY BUT WE DO NOT SEARCH FOR REPLACEMENT PARTS HERE ON FIXYA

Russell Hobbs... | Answered on Jan 21, 2019


Try a web search for the device manual. Beyond that, you will probably not have a service manual from anyone but the manufacturer.

Margaritaville... | Answered on Jan 18, 2019


I have been searching for about 30 minutes, and I reckon the company are out of business. The company headquarters were in Venezuela, but my Spanish is not that good. Nowhere appears to do spares and any reviews I find go back to around 2009.


Maillegro 9090 Immersion Blender Google Search

Blenders | Answered on Jan 14, 2019


I know this is an old, old post, but I could not find a solution anywhere, so hopefully this will help someone. We have a model 51BL25, similar to scottman55's blender, and it had the same problem. There are two separate nuts in the blade assembly. One holds the blade on, and the other holds the seal tight. When the latter gets loose, the blender shakes and leaks.
To fix it, first you have to remove the top nut holding the blade on. I had to get in there with pliers, but a ratchet with an extension would be perfect. This nut is right-handed ("normal"). Once that nut is loose, you can remove the nut and the blade. You will also want to remove the washer immediately under the blade (take note of which side goes up).
Now, you can pull the whole axle out by the wheel on bottom of the blender. This exposes a really thin, flat nut. In my case, this nut had come completely off, so nothing was really holding the seal together at all. Again, make sure you remember which direction the nut goes -- it is not quite symmetrical. That nut is what comes loose when the blender starts leaking. By the way, it is a left-handed nut, so it screws on counter-clockwise ("backwards"). Screw it in tight, then put the rest of the blade assembly back together, and your done. If you have the right tools, it should take only maybe 5 minutes.
Depending on your problem/model, this may or may not solve your problem. Hope it helps!

Blenders | Answered on Jan 07, 2019


Sometimes they can be soldered to a circuit board. If it is inline, it could look like a small metal tube with what looks like white porcelain on one end where the wire comes out. If this is present, it is a circuit breaker similar to a fuse but instead of blowing with an electrical overload, it is sensitive to heat like from an over heating motor. This may be glued to a solid part of the motor like the steel plate lamination and must be replaced. These don't reset. These can also be completely inside a piece of plastic tubing as their leads are not insulated. Good luck.

Cuisinart... | Answered on Jan 03, 2019

Not finding what you are looking for?
Blenders Logo

6,208 questions posted

Ask a Question

Usually answered in minutes!

Top Blenders Experts

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Ross Keen

Level 3 Expert

1364 Answers

Are you a Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...