Bosch Drywall - Answered Questions & Fixed Issues


Sometimes you can wrap a piece of thin plastic or paper around the stem and shove it back in and will hold it in place,- other wise there is a spring steel clip that probable wore out and would need to be replace but it wont be fun

Bosch SG45 4500... | Answered on Nov 02, 2017 | 754 views


Because the tip is brand new or you don't have a magnetic ti. Try tilting the gun a little sideways before you pull it away from the screw. Sorta like tilting a sweating glass a little bit before you lift it off of a coaster so that the coaster doesn't stick to the bottom of the glass.

Jim

Bosch SG45 4500... | Answered on Mar 10, 2015 | 1,276 views


Just pull it out. If it is rusted stuck, get a pair of pliers on there and give it a yank. It will come out.

Bosch SG45 4500... | Answered on Jul 26, 2010 | 590 views


You have to replace the entire depth guage assembly (the front plastic pieces where the bit driver is). Unfortunatly Bosch does not make the individual pieces for this gun. Any Bosch service center will be able to supply you with this piece

Bosch SG45 4500... | Answered on Apr 14, 2009 | 745 views


I don't think a Dremel has enough power to do what your after. However there is a larger rotary tool made by several different company's mine is made Dewalt works great fairly inexpensive and will do what you need.

Drywall | Answered on Sep 30, 2019 | 80 views


The stud finders are not expensive but you can sometimes use a magnet to find the nails. Also you might try shining a flashlight across the wall. The putty put over the nails will sometimes show up. Last resort is to tap on the wall and try and hear the areas that have support under them.

Drywall | Answered on Jul 19, 2019 | 927 views


5/8 of an inch is recommended. You may be able to get away with 1/2 inch if you don't really care, but i would check with the building inspector first

Drywall | Answered on Jul 19, 2019 | 943 views


Screws if you have not already used. Then as follows:
Joint compound
Joint tape
Then texture if desired
Primer
Paint

Drywall | Answered on Mar 03, 2019 | 168 views


Not if it isn’t going to show.

Drywall | Answered on Oct 07, 2018 | 310 views


you tape and mud the joints after hanging the drywall

Drywall | Answered on Jul 01, 2018 | 350 views


You can either measure up from the floor or the piece of drywall you just hang and then measure over from the wall or the piece of drywall you just hang or you can put the drywall in place and I ball behind it and Mark with a pencil and then cut it out with a dremel tool and you should be good from there. You might want to use a keyhole saw or a roto zip and a Rotozip is the best way to do it but it takes a little practice in order to control it

Drywall | Answered on Mar 01, 2018 | 1,123 views


hi there.
Sink A Self-Drilling (Threaded) Anchor
  1. Mark your hanging point with a pencil.
  2. Tap the pointed tip of the anchor into the wall with a hammer.
  3. Once the tip is in the drywall, with a screwdriver, screw the anchor in until it's flush to the wall.

Fix-It Friday: Anchors Aweigh! How To Put Anchors Into Walls

womenyoushouldknow.net/fix-it-friday-anchors-aweigh-how-to-put-anchors-into-walls/
How to Install Drywall Anchors to Hang Heavy Stuff on Your Walls
How do hang an object using drywall anchors Google Search

Drywall | Answered on Nov 28, 2017 | 511 views


many home improvement stores sell partial sheets . then you cut a plug the right size and spackle it in place .

Drywall | Answered on Dec 17, 2017 | 1,041 views


Get you some heavy duty liquid nail or similar adhesive, put it in strings/loops, wait a bit, put rock on, hold a bit done

Drywall | Answered on Apr 17, 2017 | 1,193 views


Drywall sheets are 4 feet wide. Thus, each foot of a drywall sheet contains 4 square feet. Divide 10,000 by 4 = 2500 linear feet of drywall sheets. Add 5 to 10% for wastage.

Drywall | Answered on Mar 14, 2017 | 1,154 views


2 or 3 days, plus or minus depending on how fast the mud dries.

Drywall | Answered on May 02, 2017 | 1,450 views


Cut off the loose make flat tape and drywall mud

Drywall | Answered on Mar 04, 2015 | 1,285 views


Sorry for the paint peeling and bubbles. It's not the drywall tape that has bubbles... right? Paint can react like this when it is applied over a sanded wall that has not been cleaned and still has a layer of drywall dust on it. When primer is applied to the wall, it is best to use something to push the paint on the surface to combine the dust with the paint. This could be done using a paint pad but should be more than just rolled on. The paint needs to mix with the dust and stir it in with the paint so the paint get under the dust. You might try thinning the paint a little to allow for better attraction to the wall. So now how do you repair this? By scraping the loose paint off and starting with a new coat. You know. it could also just be bad paint.

Drywall | Answered on Mar 01, 2015 | 1,310 views


First, insulation is put in on exterior walls with specific R ratings, drywall is just screwed to studs then spackled.in bathrooms it's a little different. There's different options for material backboard that are waterproof. Some are fiberglass then are finished in resin sealant

Drywall | Answered on May 05, 2015 | 1,088 views

Not finding what you are looking for?
Bosch Logo

Ask a Question

Usually answered in minutes!

Top Bosch Drywall Experts

ray gallant

Level 3 Expert

66473 Answers

John Donghia Jr.
John Donghia Jr.

Level 2 Expert

47 Answers

Are you a Bosch Drywall Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...