Black & Decker Drills - Answered Questions & Fixed Issues

The motor does not go in reverse.

hi, have you seen this ? https://support.blackanddecker.com/hc/en-us/articles/360012702998-If-my-battery-is-not-charging-what-can-I-try-#:~:text=If%20your%20battery%20is%20not,charger%20to%20try%20charging%20again. Now i don't think that's the issue , it more likely the cells won't take a charger or the bms electronic board has failed , with those battery packs it can be a electronics problem or a failed cell , One thing you might want to check is the actual connection to the battery pack..i seen a issue here where there is a bad connection , the charger won't charge regards Rob

With that being said, be advised that leaving the screwdriver on the charger after fully charged may overcharge it and also shorten its battery life. Therefore, it is recommended to unplug the unit from the charger after charging.

Question moved from Cars and Trucks. This place is good for parts https://www.toolbarn.com/blogs/parts-schematics/blackdecker-dr501-type-1-1-2-drill https://www.google.com/search?q=Black+and+Decker+model+1 ..

fixya doesent sell products repair shop or online order

Has to so it can drill the hole .

Normally when it will no longer hold a charge, that is, no matter how long you charge it, the battery goes flat very quickly. This happens sooner with Ni-Cad batteries than with Li-Ion.

If you open the jaws as large as they will go, there is a screw for fixing. It has a left hand thread!

I had this problem too, an unfortunately, there's no manual on the black & decker site for this product.
I figured it out though! You have to push down (towards the motor) the chuck collar (cyllindrical black part which holds the bit). If you've tried this already, try harder - it can get really stuck and require a lot of force to push down.
Anyways, if you apply enough force, it will give and allow you to remove whatever bit is inside.
Hope this helps.

it is probably the brushes on the motors are wore out or stuck and not making contact. pretty much junk unless you feel confident enough to attempt repair. If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

Open the chuck as wide as it will open and look inside to see what type of screw/bolt it uses then using the correct tool insert it into the chuck and undo the bolt/screw, usually it will have a left hand thread so to unscrew it needs to be rotated in a clockwise directions, hold the chuck tightly but dont use excessive force if this does not work then try unscrewing it in the opposite direction, at all times be firm but like I mentioned earlier dont use excessive force.

Good day Can you please supply more information Thank you

I'd put penetrating oil in it and tap the chuck with a plastic hammer. That should free it up.

Best rgrds, W/D

there's a button behind the trigger for locking the trigger at full speed. there's a button above the trigger for clockwise and counter-clockwise rotation. there's a button on the top for hammer mode or regular mode. Hammer mode is for concrete, it basically makes the drill bit hammer in turning the concrete underneath it to dust as opposed to cutting with a sharp edged drill bit for regular stuff like wood or metal. If yours has numbers those are for torque settings, and are hardly ever used by professionals.

I searched the internet, and that also was used for a workbench, in case there is other information to search for a manual. https://www.ebay.co.uk/itm/202391286088?ViewItem=&item=202391286088 Vintage Black Decker Plus Workmate 2 workbench Dual Height Workmate 750... http://powertool.manualsonline.com/manuals/mfg/black_decker/black_decker_drill_product_list.html

Hello, Mukund - I am answering from the USA. There is a Stanley Black & Decker (the current name of the Black & Decker Company) business in Dubai. See the location information here: http://placesmap.net/AE/Stanley-Black-Decker-197888/ You can contact them by phone and ask about a battery for your screwdriver. Best wishes.

time for a new battery

Keep turning it off and on several times at the socket sounds like you need to trick the memory Good luck

Turn the drill over and push the switch all the way in.

Close the chuck onto an Alan Key and use it to twist the drill off.