Banner Plumbing - Recent Questions, Troubleshooting & Support

here's a video on replacement... https://www.youtube.com/watch?v=NzRHMOrKRF8

1. Check that you are not turning the diverter too far or not far enough in the SHOWER direction. 2. It's possible that the the center part of the diverter that shuttles between ling up with the TUB hole or the SHOWER hole is installed backwards. In the SHOWER position the water pressure keeps it in the SHOWER position and when water pressure drops it defaults to the TUB position. When installed wrong, the water pressure pushes it to the TUB position. Hopes this helps. Let me know via message or rating (if helpful)

This is as you may have guessed, an Arrowhead sillcock.You should be able to replace the washer if you can find the bibb screw. Hold a bucket in front of asillcock and have someone turn the water on for 2 seconds. The bibb screw and what is left of the washer should shoot out. If you lose these parts, you can take the stem to the nearest plumbing supply, lowes, home depot or hardware store that carries Arrowhead sillcocks. They should be able to either give you a repair kit, or a whole new sillcock which you can take apart and just use the stem. It must be the same length to work properly. Before you install the new stem, make sure the bibb screw holding the washer in is tightened. Good luck!

You may take the red/blue colour part out and use a hex key to unscrew the handle assembly.

faucet should have allen screw hole behind or under, just look around and you will find it. they unscrew with allen wrench

use allen wrench and unscrew there. what is the problem with it? is it leaking? change washer in it.

it is due to the rubber seals on back of valve stems, they are not seating right to stop complete flow of water. just remove stem and replace. if it still leaks, the valve seat may need be replaced. most just turn out to replace ( with a square tool ) found at most hardware stores etc. good-day !

TURN OFF YOUR WATER SUPPLY, AND UNSCREW THE TOP SCREW ON THE HANDLE, THIS WILL ALLOW YOU TO UNSCREW THE HANDLE AND REMOVE ALLOWING YOU TO GET TO THE VALVE INSIDE.

better turn off the main line first, screw the ring again putting some extra pressure because usually rings are tighten so hard.you have to replace the base of the faucet.

You have a defective cartridge if you rotated it correctly,that should have taken care of your problem.You may also have the handle stop assembly on wrong this can cause that problem if you have a parts break down be sure that you have all components installed correctly.If you don't have a parts break down go to mnfr web site and see if you can get it that way or call co. talk to tech support they can tell you the problem solution or e-mail you a perts break down diagram.

Clean and or replace the cartridge. Cleaning the cartridge means taking it apart and it is much easier to just replace it but it's worth a try if you are so inclined.

The seal is not a 100% seal, but to access there are two types, one type the tub faucet screws on and the other style is retained by an allen set screw. if you have the set screw type, you will notice a slot on the underside of the faucet, at the tub wall end, look up in there. If you see an allen, loosen it and pull the faucet straight off. if no slot or allen, unscrew the entire faucet, counter clockwise (top to the left, for those digital clock people...).

Install a lock washer on it. Get one that fits perfectly.

well feel the water is it cold or hot then there should be Phillips screw on top the handle you have to pop off decorative cap or some of them unscrew then there be a larger nut unscrew that make sure the water off or you will get wet! that the baby you replace.

HOME DEPOT, DESPITE WHAT THE EMPLOYEES MIGHT TELL YOU THEY HAVE AN EXCELLENT SELECTION OF WHICH INCLUDES BANNER, TRUST ME I USE TO WORK THERE IN THE PLUMBING DEPARTMENT, AND IF THE ONE YOU NEED IS NOT IN STOCK IT ONLY TAKES A COUPLE DAYS TO GET ONE IN.

YES, HOME DEPOT... THE EMPLOYEES MIGHT NOT HELP YOU BUT THERE IS A FAUCET CARTRIDGE GUIDE THAT WILL HELP YOU FIND YOUR EXACT ONE, AND IF THEY DON'T HAVE IT IN STOCK IT WILL ONLY TAKE A COUPLE DAYS TO GET IN. TRUST ME I USE TO BE A PLUMBING EXPERT AT HOME DEPOT.

THIS PROBLEM IS DUE TO, POOR INSTALLATION,,,, THE ONLY SOLUTION IS TO ADD A SMALL VALVE IN BETWEEN THE SHOWER HEAD AND THE WALL,,, WHICH DEPENDING ON THE FINISH OF THE FIXTURE, ONLY COSTS ABOUT 15 DOLLARS AND IS VERY EASY TO DUE.... MAKE SURE WHEN PURCHASING THE VALVE THAT IT WORKS,,,,, BY TURNING IT TO THE "OFF" POSITION AND BLOWING INTO IT,,,, IF NO AIR ESCAPES IT IS GOOD...

you may have the stem in backwards,flip in around and see if this works,sometimes they only go in one way to work right.

little cover cap on center handle screw inside

Hi, You have to replace the two rubber cups in the hot&cold faucet lever. Let me know if you need more info.