I don't know web user and password for asus routers

hook a cable to port 1 and then to your computer.
open web browser and enter http://192.168.1.1
enter user info into the popup box and configure.

"The default log-in credentials for de Web Config Interface are "admin" for the username and the password you create the first time around. As with all routers, you can always restore it to default factory settings via the recessed reset button on its back."

connect to your router via ethernet cable and open your web browser. In the address bar type 192.168.1.1 which should bring up the router settings page. for user and password type in admin for both. Then navigate to the password settings and change it and save the changes.

Hi!

If you don't remeber the wireless security code, maybe you still remeber the user and password to access the web management interface of the router.
Then you have to connect the laptop to the router by using a network cable. Open a browser window, type in the IP adress of your router and check the wireless setup section. There you can find / modify the wifi security code.

If you don't know the router's IP adress, then open on your computer a ms-dos prompt and type the command
ipconfig /all

it will display your current IP adress, subnet mask and GATEWAY. The gateway adress is the router's IP adress that must be typed into the browser.

If you don't remember the user and password for accessing the router's web interface, please refer to the router's user manual in order to reset it to factory default configuration, and then proceed as for the first installation of the router.

Hope it helped,

Bogdan

You will have to perform a factory reset on the router.
Looking at page 6 of the user manual for this device, I see there is a RESET button on the back.
Use the tip of a ballpoint pen to press and hold the RESET button on the back for about 15 to 20 seconds. This will set your router back to factory defaults.
After you've done this, start the procedure on page 10 of the user manual to configure the router using your web browser.
Be sure to set-up WPA/WPA2 security on your router as described starting at page 31. If at all possible, do not use WEP security. WEP security has been cracked and can easily be cracked.

Connect youra router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi . Let me know if you need further assistance. Thanks for using FixYa.

Open a browser. Type in the router IP 192.168.1.1. Login to the router using your user id and password. If you have never set up a user id or password, then use the factory default ones to access. Once into the router settings, change the admin password to avoid anyone later accessing the router and changing your settings. Once you save the admin password change, you will be kicked out and must login again with the new password. Once in, go to wireless settings. Here you will able to set a wireless password (security key) for your wireless LAN. Once you save and exit, you will need to go to all your wireless devices and modify them with the security key in order for them to access the network. Once the key is in the router, your network is secure from outsiders getting in without knowing the key.

You need to enable WEP or WPA or WAP in wireless security. For that access your wireless router with below method. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then click on wireless then wireless security then enable WEP security enter Password then apply and save settings then restart router . Then only those can connect who know that password. . Let me know if you need further assistance. Thanks for using FixYa.

Hi,

In order to access the web interface of the router you should know the IP address of the router. Please try the following steps to check the ip address on the computer which is connected with the router (wired/wireless doesn’t matter).

1. Click on start the go to run and try cmd and click on ok.
2. Type ipconfig and press enter.
3. look for the default gateway numbers.

the default gateway is the address of the router. Open internet explorer and type http://default gateway numbers (for example http://192.168.1.1)

It should take you to the web interface of the router on which authentication is needed. The default user name and password is admin and admin.

Let me know if it help.

Rashish

you can setup your device using it's web user interface.
just open a web browser and type http://192.168.1.1. it'll prompt you for a username and password, type "admin" on both fields and it'll prompt you a web page where you can setup your internet settings and your wireless settings
(Note: your computer should be hardwired to device while doing the setps above)

hope this'll help you.
ciao!