Question about Braun Paxiscope XL Opaque Projector - 100522 Projector Lamp

1 Answer

I am changing the halogen bulb on my Braun Paxiscope-XL for the first time, following the instruction booklet, and cannot get anywhere. The bulb is tight behind a plastic "slider", and the instruction is to move the slider to the left to disconnect the bulb. But while the slider is loose to the feel, it does not move more than 1 or 2mm. left and right. Help please. Ronald

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,833 Answers

Please take help from the following: www.aandrews.com or call 1-852-2793-6400 or 1-852-2763-7901.

After feeling loose you must still try to move while keeping the pressure on the bulb. That way it will completely be removed.

Posted on Mar 04, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instruction manual KuKoocooker hood light bulbs


Just look this youtube video, and it can't be more clear.
Don't forget to unplug the hood, or switch it of. Although the halogen lamps are only 12 volt. In the hood are dangerous voltages. How to replace cooker hood halogen bulb or lamp

Sep 22, 2014 | Kitchen Ranges

1 Answer

How to replace low beam bulb on toyota avalon XL 2009


Here's what I did to change the driver's side halogen low beam bulb #9006. Do so at your own risk.


1. First ensure fuses are OK. There are four(4) 15A fuses in the fuse box under the hood - drivers side. All are clearly mapped out on underside of fuse box cover. I used the continuity tester circuit on a VOM to ensure they were OK.

2. Remove large plastic shroud that runs across from one side of the top front under the hood of vehicle to the other side. 5 plastic pins held mine in place. Once off -- you'll be able to see your vehicles radiator cap. Removing this helps provide some additional access and leverage to better work with.

3. Remove battery negative cable - 10mm socket

4. Remove battery hold down bracket - rod - one(1) 10mm bolt at front - one(1) 10mm nut on rod. Deep socket 10mm helps with the 10mm nut.

5. Remove battery positive cable - 10mm socket

6. Remove battery and plastic battery tray

7. You should see the halogen low beam bulb #9006 in front of the fuse box(drivers side). Mine has a brown electrical plug connected to it. It helps to first remove and place out of the way - the parking light which is just to the left - the assembly for mine is light gray in color. Doing so gets that wire out of the way. One less distraction when you reach in to remove the low beam halogen bulb #9006.

8. Remove electrical connection from halogen low beam bulb #9006. There's a locking tab on the bottom - press in and while doing that - push down on the electrical connector from the top. It comes off without a great deal of effort.

9. Remove halogen low beam bulb #9006 by turning counter-clockwise - looking at the bulb from the back. Mine did not want to twist loose right away. Go slowly - take your time. It should eventually come loose. #9006 bulb came out easily even with the fuse box nearby.

10. Install new halogen low beam bulb #9006. I opted for a $10 Wal-Mart Sylvania #9006.

11. Reconnect electrical connection to the new halogen low beam bulb #9006.

12. Clean battery tray and terminals on battery + connections on battery cables.

13. Install battery tray and battery

14. Connect positive battery cable to battery - 10mm

15. Connect hold-down and rod + one(1) 10mm bolt at front and one(1) 10mm nut that goes on rod at rear.

16. Connect negative battery terminal - BUT - before doing so - have your remote locking/unlocking device handy. As soon as you connect the negative battery cable to the batteries negative terminal - the horn will sound(alarm). Quickly depress the UNLOCK button on your vehicles remote. Finish tightening the negative cable. You should also see that the low beam is once again functional as it will come on when the alarm is sounded.

17. Reinstall large plastic shroud and all lock down tabs

18. Start car and set clock/radio settings/etc.

19. There is a procedure to resync the power windows. The following provided by inov8 from another forum.

Copied from TSB PD002-05

NOTE:
Anytime the battery terminal has been disconnected, please initialize the driver's door
power
window and front passenger's door power window after reconnecting the
battery terminal.

With ignition switch in the "ON" position, do the following:

1. Push down and hold the driver's door power
window switch to completely open
the
window.
2. Pull and hold up the driver's door power
window switch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully
pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power
window switch for the passenger's door window should
be blinking.
4. Push down and hold the passenger's door power
window switch to completely open
the
window.
5. Pull and hold up the passenger's door power
window switch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully
pushing the switch briefly to the "DOWN" and "UP" positions.

Sunroof initialization is similar.


20. There is a procedure to resync power seats. Extracted from factory service doc:

Using seat switches - fully slide seat fwd. - fully recline seatback fwd. - fully raise seat cushion and head rest.

Using seat switches - fully slide the seat rearward - fully recline the seatback rearward - fully lower seat cushion and head rest.

Jun 14, 2012 | 2009 Toyota Avalon XL

1 Answer

I need the instruction booklet for the Braun MX250 blender.


http://www.service.braun.com/home.asp?rg=NA&c=US&l=GB&typ=ui&s=&seite=&sString=
hope this link helps. it's the braun website. you will probably need the model number.
thanks,
mike

Jul 08, 2011 | Microwave Ovens

1 Answer

How to change a front turn light in a 1996 taurus.


Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation
  1. Remove Headlamp (13008) as outlined.
Headlamp Assembly
Removal and Installation
  1. ani_caut.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
  1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
  1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.


    Headlamp Assembly (Taurus Shown, Sable Similar)


    k24744a.gif
  1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
  1. Remove screw from park/turn signal housing.
  1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
  1. Remove parking lamp from vehicle.
  1. To install, reverse Removal procedure.


    Front Lamp-Lamp Assembly, Taurus


    k23818a.gif

Nov 19, 2010 | Ford Taurus Cars & Trucks

2 Answers

Replace front headlight


Headlights Removal & Installation WARNING
Halogen bulbs contain a gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments.
To help avoid personal injury:
  • Turn off the headlamp switch and allow the bulb to cool before changing bulbs. Leave the headlamp switch off until the bulb change is complete.
  • Always wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • Do not drop or scratch the bulb. Keep moisture away.
  • Place the used bulb in the new bulb's carton and dispose of it properly. Keep halogen bulbs out of the reach of children
To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • LH and RH engine under covers
    • RH and LH Front fender liners
    • Front bumper cover
  3. 2 bolts and disconnect the connectors
  4. Headlight assembly by pulling it forward
  5. To Install:
    1. Install or connect the following:
      • Headlamp assembly
      • 2 bolts and connector
      • Front bumper cover
      • LH and RH front fender liners
      • LH and RH engine under cover
2997275.gif

Jul 25, 2009 | 1998 Toyota Camry

1 Answer

During the initial set up of the tomtom one xl s i accidently set am instead of pm. How do i change it from one to the other.


Boot up your tt, tap the screen anywhere, then tap change preferances, tap the forward arrow until you see set clock. Tap set clock and then follow the instructions.
Hope this helps

May 12, 2009 | Tomtom ONE XL-S GPS

1 Answer

I do not know how to access and change the light in a standard smeg microwave, model number SA35MX Note: ther is no instructions in the operating instruction booklet for the microwave.


Manufacturers used to include access panels in the rear or side so you could easily change the bulb. That exposed the customer to line voltages, and that posed a real liability threat, so they stopped using them.

You now must generally remove the outer cover to replace the bulb.

In many over-the-range models, that can mean having to take the oven down from the wall! For safety's sake, that should be a two-person job and it's really helpful if you have your original installation instructions to do this.

Many models use halogen lamps. You must not touch the new one with your bare skin as the oils will shorten the bulb life.

We're happy to help and we appreciate your thoughtful rating of our answer.

Apr 26, 2008 | Microwave Ovens

Not finding what you are looking for?
Braun Paxiscope XL Opaque Projector -  100522 Projector Lamp Logo

Related Topics:

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Braun Office Equipment & Supplies Experts

Ekse

Level 3 Expert

13434 Answers

Cindy Wells

Level 3 Expert

6065 Answers

jasbo
jasbo

Level 3 Expert

2239 Answers

Are you a Braun Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...