Dear Sir or Madam,
My friend gave me his D-Link DWL-2100AP, H/W Ver: A2 F/W Ver. 2.00. I reset the unit so it can go back to its default settings. I have a wired router in my office (NetGear) that I can connect this unit to one of the pc's that is not being used and then I can have internet access using 'default' network with my MacBook Pro. My problem is that i need to set up a password to give it some security because when this unit is plugged in, anyone can use it to access my other office computers and it could be disastrous.
I don't know how to connect it so i can access it's menu to configure. I tried directly connecting the unit to my pc and also directly connecting it to my Macbook Pro laptop. Of course, no luck. Any ideas would be greatly appreciated. Thanks.
Here is what you can do. You need to access the setup page of your Dlink Access Point.
1. connect a computer directly to the access point (via ethernet). Then assign an IP address on the computer (IP: 192.168.0.10 Subnet Mask 255.255.255.0 DG: 192.168.0.1 ). It is necessary for you to assign an IP address because your access point does not have the ability to assign an IP address to the a computer, its is not like a router.
2. After you assigned an IP address, you can now access the Dlink Access point's setup page. To do that open your browser in the address bar type http://192.168.0.50 (this is the address of your access piont) and it will ask you to put a username and password. Just type admin for both username and password field. And it will take you to the setup page of the access point.
3. To enable a wireless security, just click the tab on the left hand side that says Advanced, it will populate the options under Advanced and select security. On the main screen you will now have an option for security modem, you can select wpa-psk, then on the Key box you can type any password that you want (8-63 characters). Then click update there at the bottom of the page. If you also want to change the name that the Access point is broadcasting you can go to the on the left hand side that says Wireless and put any name that you want on the box that says SSID. After that click updat button again.
4. Now after updating the settings, You can reconnect to the network. And this time you will now be asked for the network key. Just type your network key. That's it.
Just reply to this post in case that you need more help.
You're welcome!
there is alot of possible reasons why its happening... it may run a bit slower if you have a security but not same as a speed of a dialup connection. Have checked if you are getting at a good or very signal? Try to change the channel try channels 1,11. check if there is an interference like cordless phones running on 2.4 ghz. Does all of your wireless computers is experiencing the same problem?
Very nice info. Work like a talisman
Hi Jeffrey, I have one problem. I cannot connect to 192.168.0.50. I did everything that you have mentioned. But the bloody browser wont open the link. without the link i cannot configure my AP. Please help. thanks in advance. Cheers
×
In order not to need to change any settings on the computer, simply connect the AP to the internt via an ethernet cable connected to the router.
And then proceed by writing 192.168.0.50 on the computer, etc.
After saving settings of the AP, disconnect ethernet cable.
Hence, no need for any changes in the computer`s settings, even if we are talking temporary changes!
Otzenklotzen
Hello, this will help you. http://support.dlink.com/emulators/DWLG700AP/h_wizard.html
have fun
Hi there!
Any one has an idea why I can't connect to website http://192.168.0.50 ?
It directs me to ICQ Search site, so it means can' find site...
Thank you!
Dear Sir or Madam, I Have a D-Link DWL-2100AP, H/W Ver: A4 F/W Ver. 2.20. I reset the unit so it can go back to its default settings. I have a wired router at home that I can connect this unit to my pc and a notebook that is not being used and then I can connet to the internet. But I'm failing to get to the we address given in the quick setup.
I can't configure my accesspoint from private default ip to secure one ?how can i secure it and make it a repeater at where the siginal ends to extend the signal to where i stay at about 120m?
Also this problem
SOURCE: can't connect to configure password through web address 192.168.0.50
When you reset the AP, how long did you press the reset button? To reset the AP to factory defaults, the reset button should be pressed and held for at least 15 seconds. Also, once reset, the AP should have the following settings:
IP address: 192.168.0.50
Subnet Mask: 255.255.255.0
Default admin username: admin
Default admin password: <blank>
When connecting your PC, either set an IP address within the same subnet (192.168.0.51 255.255.255.0) or choose "Obtain address automatically".
I hope this helps.
Dave Grannas
48,897 views
Usually answered in minutes!
Thanks tech curly for your very prompt response. You helped me connect to this access point. It wasn't displayed in the same way as you had seen because I probably had an older version. I did have to type 'admin' for username but i had to leave password field blank. Thanks again for all of your help. I just found this web site today.
Dear Tech,
Thank you for helping me secure this access point, but now i find that when I try to use it to surf the net, it takes a very long time to connect to various web sites (almost like using a dialup modem) even though i have a cable connection. Sometimes it even times out. Any suggestions would be appreciated.
When I reset the access point back to it's default, it connects quick.
Thanks for your help.
wireless
Ineed
dont have any idea regarding this device and kind a misfortune i got this device to be installed for the laptop
any advice or help would be gladly appreciated. thanks
same Problem
how to put a passwword on the access point ?
i have a eh100 router and was given this code to setup my laptop...but it just keeps saying cant find server,yet all the rest of the internet is working!
hi sirs
i have a problem with connecting the acces point DWL-2000Ap 802.11g/b the internetis working but i couldn't configure or set my username and password
i need ur help plz
best regards
when i type http://198.162.0.50 i am not able to connect. it says check your connection.
Regards
Ancel
i have th same probelm with a dwl-8200 ap i cant access it.
i have even tried to make a ping ot it and it does not work.
I have reseted the device and i have assigned and IP address to the computer from whih i tried to access it and yet nothing
any ideas?
I am tring to reset my dlink dwl-21oop i tap in the usual http:// code but to no avail. No logo pops up, no set up wizard. Any ideas?
Sami mawon mboten saget di password. Pripun niki mumet mas!!!
fgh
same problem, have access to the Internet but I can't get to 192.168.0.50 to configure router security. thanks!
cannot connect to configure password through web address 192.168.0.50
can't connect to configure password through web address 192.168.0.50
I have a D-Link DAP-1522 Wireless Bridge and can't connect to the Configuration Utility at DLINKAP or 192.168.0.50: both addresses will not access the needed web site?? What is the problem with this address?
Struggling to set it up
need add passwerd
×