Remove washer pedestal drawer - Washing Machines

Question

Question about Washing Machines

2 Answers

Remove washer pedestal drawer - Washing Machines

1 more comment
Anonymous Oct 14, 2008

Cannot remove drawer from Frigidaire pedestal.
Not found in the instructions.
HELP!!
Anonymous Jan 02, 2009

i have the same problem. It is very annoying as i am only able to remove the detergent dish. But i really need to remove the whole drawer so as to give it a good clean. can any one help!!
Anonymous May 05, 2009

Our pedestal drawer won't close all the way. We want to take the drawer out to see if something fell behind it to stop it from closing. We can't get the drawer out.

×

2 Answers

Anonymous

Level 1:

An expert who has achieved level 1.

Mayor:

An expert whose answer got voted for 2 times.
Contributor
1 Answer

Ok ladies and gents.I have a kenmore 45862400 that went on me.The dreaded bearings.Had to take the pedestal off so I hopefully can use it on a new whirlpool thats coming today.You have to take the draw front off.6 screws inside and 1 on each of the sides.Once you take this off pull the draw out and its sits in there like a tube.By the way machine lasted almost 5 yrs.Stripped it of all parts.Mom and cousin have the same model.Good luck.

Posted on Aug 04, 2009

6 Suggested Answers

6ya staff

2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Richard

413 Answers

SOURCE: need to remove drawer from

There are two ways this drawer is held in place;

Open the drawer fully. Look at the rear of the support slide is there a small, black plastic lever? If so, on one side push the lever down, the other side pull the lever up. (sorry don't remember which side up or down)
No lever? Remove the small screw on either side of the support slide at the front of the drawer. Lift the drawer and push support slide away from the drawer.

If you need further assistance, let me know

Regards;
reg501
The FixYa Team.....

Posted on Jun 24, 2008

Anonymous

1 Answer

SOURCE: Samsung Pedestal Drawer

If you pull out the drawer (completely) you should find 1 or 2 screws on each side that bolts the slider to the drawer. Remove these, then lift out the drawer. This then gives you full access inside. ...JimS

Posted on Aug 04, 2008

Anonymous

1 Answer

SOURCE: Washer is off balance. Need to get to levelers.

Remove the two phillips screws inside the front right and left side of the drawer. They have 3/8 nuts holding them to the drawer rails. The drawer separates from the rails and comes out, leaving the rails attached. The levelers can be adjusted with a 1/4 inch wrench after loosening the 9/16 locknut under the base. This drove me crazy too, until someone mentioned taking the screws out as a step in removing the entire pedestal. For what it's worth, I posted this question to sears online and received an email saying: Unfortunately, we are unable to provide you with the information you
have requested.

Posted on Jan 05, 2009

Anonymous

82 Answers

SOURCE: How can I remove the Whirlpool Duet washer pedestal drawer?

there should be a clip on the top or bottom if not pull it out as far as it will go grab it on both sides and pull sharpley towards you DO NOT GRAB THE FRONT IT WILL BREAK

Posted on Jun 29, 2009

Anonymous

1 Answer

SOURCE: how to remove drawer on pedestal

You need to remove the 2 screws holding the black rails on both sides of the drawer. Took us a while to figure this one out also.

Posted on Jan 31, 2010

Add Your Answer

Upload

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

How do I remove a pedestal drawer on and electrolux dryer

Hello friend, thanks for your inquiry!

I have researched that information for you and was unable to locate steps on how to remove the drawer from your pedestal. I would suggest seeking assistance from a professional for proper removal of the drawer. Hopefully this helps. -Matt

Sep 28, 2014 | Electrolux Washer/Dryer Laundry Pedestal...

1 Answer

Remove washer pedestal drawer Cannot remove drawer to check behind or underneath, please help.

Open the drawer fully. Look at the rear of the support slide is there a small, black plastic lever on one side push the lever down, the other side pull the lever up.
Remove the small screw on either side of the support slide at the front of the drawer. Lift the drawer and push support slide away from the drawer

Oct 30, 2008 | Whirlpool LAB2700ML Pedestal Drawer for...

1 Answer

How do you install whirlpool duet pedestal

Make sure that you get the pedestal designed for your washer. The white pedestal for the GHW9400P would be LAB2700MQ. (There are slight differences in the pedestals for different series washers. The holes in the base of the washer will not line up with the holes in the pedestal for a mismatched combination.)

First if your washer has been installed, uninstall it. You need to turn off the water. Then disconnect the power cord and (carefully) the fill hoses. Loosen the hoses first and then completely remove them. Drain the hoses into a bucket. Disconnect the drain hose from the back of the washer. Use pliers to squeeze the clamp to get the drain hose loose.

Pull the washer away from the wall. Cover the area behind the washer with cardboard and tip the washer onto its back (on the cardboard).

Pull out the drawer of the pedestal. Next snap the spacers into the holes on the top of the pedestal. (These are part of the hardware kit in the drawer of the pedestal.) Remove the shipping spacers from the front of the pedestal (behind the drawer). Remove the Philips head screw from the drawer slides and pull the drawer completely out (save the screws). Push the slides back into the pedestal.

Look at the washer and remove the feet if present. Partially install two of the hex head screws from the pedestal installation kit in the bottom holes of the washer. (These are at the center back of the washer if it is standing up.) Leave the screws about 3/8" from the bottom of the washer. Move the pedestal over to the washer and slide the keyhole openings of the pedestal over the two partially installed screws. Position the pedestal against the top of the washer and insert the remaining two hex head screws. Do not tighten completely.

Align the pedestal with the base of the washer on all sides. When it is lined up, tighten the 4 screws by reaching through the drawer opening of the pedestal. Bring the washer and pedestal back upright. Reinstall the washer (remove the packaging if this was a new install). Level (front to back and side to side) the washer using the pedestal feet (again reach through the drawer opening). Make sure that all 4 feet touch the floor. Tighten all 4 locknuts.

Pull out the drawer slides and reinstall the drawer. Reinstall the Philips screws. Close the drawer.

For pictures of the install, go to the Whirlpool support site http://www.whirlpool.com/owner_center . Search for your pedestal and get the installation manual. The direct link for the LAB2700MQ0 install is http://www.kitchenaid.ca/assets/pdfs/literature/Installation%20Instructions%20-%208537141.pdf .

I hope this helps.

Cindy Wells

Aug 04, 2011 | Whirlpool GHW9400 Duet Washer

1 Answer

LAB2700ML Optional Pedestal Drawer for Duet® Washers & Dryers PEWTER: How do you remove the drawer?...

how does the drawer come out of the base

May 17, 2010 | Whirlpool LAB2700ML Pedestal Drawer for...

1 Answer

Installing pedestal to washer

You want to level just the pedestal in the place where you will be using it so when you put it in position mounted together later it is done. Also very easy to do first. Get the pedestal level, tighten the lock nuts, put the washer on its back. Usually you remove the washer feet, take the pedestal drawer out, screw on each side, bolt the pedestal to the washer with the four screws provided. Tip pedestal and washer up, on to something that slides easily to protect floor. There usually are some type of shipping bolts that have to be removed from back of washer before using on new units. Usually four and these have to be removed.

Jan 13, 2010 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

How to remove drawer on pedestal

You need to remove the 2 screws holding the black rails on both sides of the drawer. Took us a while to figure this one out also.

Jan 01, 2010 | LG WM2487HWMA Front Load Stacked Washer /...

1 Answer

How do you remove the washer from the pedestal?

not an easy task---try to remove the drawer. there is a bolt going upwards in each corner (inside)

Dec 10, 2009 | Whirlpool LAB2700ML Pedestal Drawer for...

2 Answers

How can I remove the Whirlpool Duet washer pedestal drawer?

When you look this will not appear to be how it is done but it is in fact the way. Pull the drawer all the way out and then look on the side of the drawer at the very front and you will see a single small screw that attaches the track to the drawer. It would appear this is part of a series of screws and the track itself should seperate but neither side of the track removes. Simply remove these screws on both sides of the drawer with a small hex head socket and the drawer will pull right out. Push the tracks back into the pedestal until done cleaning the drawer.

Jun 29, 2009 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Samsung Pedestal Drawer

If you pull out the drawer (completely) you should find 1 or 2 screws on each side that bolts the slider to the drawer. Remove these, then lift out the drawer. This then gives you full access inside. ...JimS

Jul 31, 2008 | Samsung WE356A5W Washer/Dryer Laundry...

1 Answer

Remove pedestal drawer from washer

First remove the top of the washer via 3 tork, 7mm hex head screws (they are hidden located on rear of washer) then you can see to line up the tub with the shipping bolts. Just put 2 in --one lower and upper opposing each other and that will be sufficient. I believe there is two screws holding the drawer in located at the track towards the front of the drawer. Now you can lean it over with no worries to remove pedestal

Jan 12, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?

View Most Popular

Washing Machines

How do I remove a pedestal drawer on and electrolux dryer

Electrolux Washer/Dryer Laundry Pedestal with Storage Drawer - Island White EPWD15IW

Open Questions:

0 Answers

How do you remove the agitator on a speed queen model AWN412SP111TW01

Dec 02, 2019 | Speed Queen Washing Machines

0 Answers

I have a fridgadair # FFLE4033QTO we have replaced the main board twice first time it worked for a month this NEW one the washer wont start when we plugged it in there was 3 long beeps

Dec 02, 2019 | Washing Machines

0 Answers

FILL WATER TANK ERRORon my TREVI DIGITAL PLUS Ex. I have opened the unit and connected a 2 prong plug with the wires twisted together to the #4 Spot on the Computer board. STILL DISPLAYS FILL ERROR.

Nov 20, 2019 | Washing Machines

0 Answers

He5 front load washer won't start; just beeps. Was working fine. I took it off the pedestal and stacked the dryer on top. Now I just get three beeps from the power button, no display. I followed steps to test Motor Control Unit but still now power up. Wondering if there is a sensor that does not like the unit to be laid down

Nov 17, 2019 | Washing Machines

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey

Level 3 Expert

1481 Answers

Marvin

Level 3 Expert

85216 Answers

Brad Brown

Level 3 Expert

18127 Answers

Have a manual for Washing Machines? Or just drag it here!

Anonymous · Accepted Answer · 2009-05-11T16:52:07.2000000Z

Anonymous

Level 1:

An expert who has achieved level 1.

Mayor:

An expert whose answer got voted for 2 times.
Contributor
1 Answer

I have a GE front loader on a pedestal & needed to remove the drawer. I got an answer from their website below. Basically, on this model, unscrew the hex-head screw at the FRONT of the side rails on each side.
http://products.geappliances.com/ApplProducts/Dispatcher?REQUEST=SPECPAGE&SKU=SBSD137HWW&SITEID=GEA&TABID=4 Manuals & Documentation tab - page 2

Posted on May 11, 2009

tallpines344 Aug 30, 2010

HELLO MR SSOTT THANK YOU FOR THE INFO MAY GOD BLESS YOU.
MR.BOB

×

Remove washer pedestal drawer - Washing Machines

2 Answers

6 Suggested Answers

Add Your Answer

Attachments: Added items

Related Questions:

How do I remove a pedestal drawer on and electrolux dryer

Remove washer pedestal drawer Cannot remove drawer to check behind or underneath, please help.

How do you install whirlpool duet pedestal

LAB2700ML Optional Pedestal Drawer for Duet® Washers & Dryers PEWTER: How do you remove the drawer?...

Installing pedestal to washer

How to remove drawer on pedestal

How do you remove the washer from the pedestal?

How can I remove the Whirlpool Duet washer pedestal drawer?

Samsung Pedestal Drawer

Remove pedestal drawer from washer

Not finding what you are looking for?

Washing Machines

How do I remove a pedestal drawer on and electrolux dryer

Open Questions:

How do you remove the agitator on a speed queen model AWN412SP111TW01

I have a fridgadair # FFLE4033QTO we have replaced the main board twice first time it worked for a month this NEW one the washer wont start when we plugged it in there was 3 long beeps

FILL WATER TANK ERRORon my TREVI DIGITAL PLUS Ex. I have opened the unit and connected a 2 prong plug with the wires twisted together to the #4 Spot on the Computer board. STILL DISPLAYS FILL ERROR.

Related Topics:

Ask a Question

Popular Questions

Whirlpool Cabrio Washer Error message code F1

Whirlpool Duet Sport Washer will not drain - F-21 error

Why is the fault F18 error code on my bosch washing machine flashing?

F 11 error code on Whirlpool Duet - Serial Communication Error ?

Washing machine will not drain

Top Washing Machines Experts

Gerry Harvey

Marvin

Brad Brown

Are you a Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides

BOSCH WFL 1262 ZA.pdf....

BOSCH WFL 1262 ZA.pdf....

Neweb06a92c-9c1f-42ed-b88d-bd15511c8ac...