Can water flow be adjusted water comes out very sl...

There is help here, but this is a very specialized RV toilet system.

https://www.google.com/search?q=tecma+toilet+has+a+slow+drain+of+water+in+bowl

,,

If the water pressure coming out of the steam/hot water arm is fine, then the issue is likely with the brew unit or the grinder. Here are a few things you can check:

1. Clean the brew unit: A dirty or clogged brew unit can slow down the flow of water. Remove the brew unit and clean it thoroughly, making sure to remove any coffee residue or buildup.
2. Check the grinder: A dull or clogged grinder can also slow down the flow of water. Make sure the grinder is set to the appropriate setting for your coffee beans and check that the grinder is not clogged.
3. Check the water flow meter: The water flow meter measures the amount of water flowing through the machine. If it is clogged or damaged, it can affect the flow of water. Try cleaning the water flow meter with a soft-bristled brush and see if that helps.
4. Check the water filter: If your machine has a water filter, it may be clogged and affecting the flow of water. Replace the filter if necessary.

If none of these solutions help, it may be a more serious issue and you may need to bring your machine to a professional for repair.

The Speed of a Navigator is adjusted by water flow. There is no adjustment on the unit itself. The more flow through the unit the faster it will go. If the unit moves too fast or too slow proper cleaning may be sacrificed. The proper flow can be achieved using the flow meter that comes with the unit.

Many pools are set up with multiple shut-off valves in front of the pump. These regulate flow from bottom suction lines, skimmer suction lines, and vacuum suction lines. If you have these valves, make sure the valve on the line the vacuum is attached to is fully open and then adjust the flow by closing off the other valves slowly until proper flow is reached. This is where the flow meter is used.

If there are no valves and the Navigator is moving too fast, an in-line valve is also supplied with the unit and can be used to regulate the flow. This valve is installed between the vac hose and the port where the vacuum is connected to the pool (side port or skimmer).

https://www.hayward-pool.com/pdf/manuals/PoolVac-Classic-XL-NavigatorPro.pdf

there is a small setting on the icemaker module, but it only makes a VERY small difference. you would want to fix the water supply issue though. the icemaker fills a ceartain amount of time, not to a level, so if you increase the time, it is still filling so slow that it won't make a big difference.
3 possibillities for slow water flow
1. flow coming into the fridge is too low- plumbing issue, likely at the water valve under your sink.
2. Water filter needs to be changed every year
3. Bad solenoid valve in the fridge. it is where the water enters the fridge.

You cannot adjust the pressure on the toilet. But you can adjust the stop setting screw at the top of the float arm. If the water is coming in too fast you can adjust the valve where the toilet water line connects to the wall water supply. Closing the valve a little will slow down the flow of water and it will take a little longer to refill the toilet water tank.

The pump is a vibratory pump and it will make some noise.

Take the lid off the reservoir and watch at the hose coming from the relief valve (the short hose).
Pull a shot.
If water comes out of the hose, the relief valve is opening on high pressure. The pump gets extra noisy on high pressure too. This happens when the water flow is blocked due to coffee ground too fine, coffee tamped too hard, pluggage somewhere.
Pull another shot but this time with the basket removed from the portafilter.
If there is still water coming out of the short hose, you need to descale the machine. If there is not water com ing out of the hose and the pump is quieter, adjust your grind or your tamp.

Take the cup warmer off the top and find where the water line comes into the machine, follow this line to a tap that has a screw in knob. If you turn the know clockwise it will slow the flow of water to the hot water spigot.

If you have replaced the parts on your pool cleaner, it is probably going to be an issue with the water flow. Check the water flow with your waterflow gauge and adjust it if necessary. See step 6 in the owners manual below if you are not sure how to adjust your water flow.

http://www.backyardcitypools.com/images/hayward/Navigator-manual.pdf

You can adjust the flow rate of water into condensor. If you can check the pressures of the freon, psi low slow water feed to condensor. IF psi high increase flow of h2o.

Clean the coils under the ice box so that the flow of air cools the condenser mo propah my amigo.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61