Question about Inverter KEB COMBIVERT F5

1 Answer

I have a prblem in the F5 keb combivert it's show Error E.OC & E.puci & E.Puch could you please advice us with the proper solution thanks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 4 Answers

E.puci During the initialization the power circuit could not be recognized as invalid.
E.puch power unit changed
power unit identification was changed, with a avalid power circuit this error can be reset by writting to SY.3. If the value displayed in SY.3 is written, only the power-cricuit dependent parameters are reinitialized. if any other value is written, then the default set is loaded . On some systems after writing SY.3 a power-On -Reset is necessary........
E.OC Overcurrent

Posted on Jun 08, 2013

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

jiha207

  • 1 Answer

SOURCE: Hi i m using keb

Hello!
What shall I do to communicate with a Combivert F5. I have tryed with different cables without success.
RPN/ Sweden

Posted on Nov 26, 2010

Anonymous

  • 332 Answers

SOURCE: F5 keb inverter problem

check you owners manual there should be inline fuses that maybe bad

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

KEB COMBIVERT F5 - Standard communications connections


Here is an overview of the the items required to communicate with the KEB COMBIVERT F5.

***X4A and X6B connections require special cable from KEB. This is a 24Vdc connection and will damage your PC/inverter if the proper cables are not used.**

ad10431d-43ae-4699-bcb1-4a77a495164b.jpg

on Feb 21, 2014 | Inverter KEB COMBIVERT F5

Tip

E.puci error


E.puci = Power Unit Code Invalid.

When the inverter is powered up the power stage can not be identified by the control card or the power stage is the wrong type for the control card.

Typically can not be reset and unit needs to be repaired or replaced.

Contact OEM of machine or KEB for additioanl support

on Feb 21, 2014 | Inverter KEB COMBIVERT F5

1 Answer

E OC error in F4 KEB


Error. Over Current - Peak current exceeded

Possible causes:
Motor has a short - Phase to phase or phase to ground.
Motor cable damaged/defective.
Motor cables too long.
Acceleration/deceleration ramps too short.
Damaged output phase of inverter.
EMI

Mar 05, 2014 | Inverter KEB COMBIVERT F5

1 Answer

Inverter keb combivert f5


What is the actual problem you are having?

Jan 31, 2014 | Inverter KEB COMBIVERT F5

1 Answer

Need a Way to adjust dr.2 Rated Motor Current value. Combivert F4-C


It sounds like you may have a thermal issue causing the fault trigger of the E.OC error. This coould be an issue with the motor or the inverter getting too hot. Once the system trips into error it is allowed to cool a little and you can run again for a while.

What is the actual part# and serial # of the inverter that you are having problems with?

Since they system has been running, I would not suggest aultering the voltage/hz curves in the inverter because of an E.OC error.

Dec 28, 2013 | Inverter KEB COMBIVERT F5

1 Answer

Oc error please help


What software are you using

Did you download the bin and language files

What cable/operator are you using

Oct 23, 2013 | Inverter KEB COMBIVERT F5

1 Answer

KEB 07 F5 Error code E. Puch what will cause this error and how do i clear it


E.puch means that at power up the control card did recognized the power stage as different than last time it powered up.

This is normal when the control card is changed. If the control card has not been changed, there is a problem between the power stage and the control card.

Initialize the value at sy.03 to reset the error.

Apr 25, 2013 | Inverter KEB COMBIVERT F5

1 Answer

Keb f5 e puch


Look under the E.puch tip section.

Feb 24, 2012 | Inverter KEB COMBIVERT F5

4 Answers

F5 keb inverter problem


i have a prblem in the F5 keb combivert it's show Error
E.OC & E.puci & E.Puch could you please advice us with the proper solution
thanks

Mar 10, 2010 | Inverter KEB COMBIVERT F5

Not finding what you are looking for?
Inverter KEB COMBIVERT F5 Logo

Related Topics:

625 people viewed this question

Ask a Question

Usually answered in minutes!

Top Inverter Electronics - Others Experts

ray gallant

Level 3 Expert

66054 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

30318 Answers

Are you an Inverter Electronics - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...