Shorting fault Hotpoint first edition 1000

The issue with the Hotpoint Aquarius WDL540 Washer/Dryer tripping the electricity during the fast spin cycle could be due to several factors. Here are some steps you can take to try to resolve the issue:

1. Check the drum balance: Make sure the load is evenly balanced in the drum. If the load is unbalanced, it can cause the drum to spin unevenly, which could trip the electricity.
2. Check the motor: If the motor is not functioning properly, it could cause the machine to trip the electricity during the fast spin cycle.
3. Check the belt: If the belt is loose or damaged, it could cause the drum to spin unevenly, which could trip the electricity.
4. Check the suspension: If the suspension is worn or damaged, it could cause the drum to spin unevenly, which could trip the electricity.
5. Check the wiring: If the wiring is damaged or frayed, it could cause a short circuit, which could trip the electricity.

If you're unable to resolve the issue with the above steps, it's possible that the machine may need to be repaired. In this case, you may want to consider contacting Hotpoint customer support for information on repair options.

If it trips the RCD then you have an electrical fault. Washing machine can do this once they are a bit old, or if they have had a water leak. The water gets into the electrical equipment and causes a fault that trips the RCD. If you have a circuit without an RCD try that. If it still trips, then the fault is serious and you will need to get it repaired. You can also try putting the washing machine into a warm place for a few days to see if it will dry everything out. Sometimes this will cure a fault if it is due to dampness.

Obviously a dead short somewhere. The only way to locate what it is , is with a multimeter. or by trial and error. Disconnecting 1 component at a time until it stops tripping the breaker. Not a very professional way but it works. I would start with the heater element first and then the motor. Make sure any wires that are disconnected are not touching anything and make sure its unplugged when you go taking wires off. Be safe , if you are not sure, get a Tech in.

Sounds like dead short on motor possibly armature,,look for burn out on segments easy to notice

run the machine, after it trips, unplug and carefully touch the motor,it may have a bad capacitor, or dry bearings causing it to draw excessive current,if these 2 things are not it, then look for a bare wire that may be touching case during this part of the cycle,and if you can get an "Amprobe" it reads current and check machines current draw during the start to trip current

Hiya,
without the make and model number its hard to tell exactly what the fault is,
Generally this is caused by a siezed motor, could be something got into the impellar or worn out.
When you say trips out, do you mean electrics trip?
If so, you have probably had a leak in the base of the appliance and shorted the motor.

Hope this helps.

Regards
Sussex engineer...
Please rate my help.

First unplug your washer. Check the ground on the washer and make sure it isn't loose; this would be a good time to inspect the wiring harness for any problems. Next check the outlet (turn off the electric to that breaker first) make sure all the wires are tight and are making good contact; pay special attention to the neutral (white) wire. If that seems fine, and you are comfortable with going into you breaker panel, turn off that breaker and check the hot (the wire on the breaker) to make sure it isn't loose and then check the neutral wire. If either of these wires seem loose tighten them down....a loose wire will move when a load is put on it and cause the breaker to trip. If all seems normal and washer is still tripping the breaker you might want to replace the breaker.....they can go bad. Good luck!

Ok that rules out the heating element. There are a number of possible causes so bear with me while i go through them.
Can you open the door? If so leave it open then turn on the machine. Does it trip?

Is it possible that water has gotten inside the controls that could have caused the flashing lights? Kind of like spilling water on a calculator, everything seems to go haywire.

hotpoint aquarius 1000 if motor is connected (plastic plug in socket) RCD earth trip trips in main board when washer is switched on, trips as soon as water starts to fill.