Question about KitchenAid KSM150PS Artisan Series Stand Mixer

1 Answer

Slow speed unattainable

Hi there...

I live in Australia and own a 240V Kitchenaid mixer and the slow speed always creeps up and it does not maintain a Speed 1/Stir speed. I've tried adjusting the speed plate and it won't slow down. Is it the fault of the governor,speed plate or phase control... Hope you could help and your time spent is much appreciated...

Thank you

Prem (premanand2009@hotmail.com)

Posted by on

  • deborah3604 Mar 30, 2008

    I still have 5 speeds, but the speeds are much faster than they were before. Speed 1 is now about the speed of speed 3. Any ideas or suggestions?

    Thanks.

  • ThomasP Apr 10, 2008

    KSM150PSOB speed 5 and up work. Mixer will not run on low speed settings. Do I need the speed control switch" #PS889134? How difficult is this part to install.



    TimP USA

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • KitchenAid Master
  • 1,364 Answers

Aussie helpline
1800-990-990

Posted on Jul 25, 2017

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 9 Answers

SOURCE: won't shift speeds

ok so the set-up looks sortof like this (lets hope the formatting of this website/your computer doesn't mess it up...)
       C           D
        /  /    \  \   \/                                    |    | ___   /\ |    |   <B
  A
A is the rivet holding the arm to the plastic body B is the contact with a little tab. C is the copper arm D is the arm's contact
there is a copper arm (C) that has a contact on one end (D).  If this contact is ALWAYS open (should only be open when mixer is off) it is either bent (carefully reform) or has come loose at the rivet marked A.  On mine, the rivet at postn. A had come loose, i simply rotated it so that the contacts touched and super-glued the copper to the plastic (which should be rivited).
Since the copper was not discolored, I knew that the temps should not be too high for the super glue to handle (not in my opinion anyway). 

Posted on Jan 26, 2008

Anonymous

  • 1 Answer

SOURCE: kitchenaid mixer speed

I have the same problem. I contacted KitchenAid they blew me off with
"I am sorry to have learned you are experiencing problems with your KitchenAid product.
Your model and serial number indicate that your 2005 model Stand Mixer is outside of the warranty period, however you may find the part or repair for your appliance locally by contacting an authorized repair center in your area. To locate an authorized repair center please click on the following website link:

http://caservice.kitchenaid.com/
They obviously have a defective poor product now and will not stand behind it!!!

Posted on May 10, 2008

Anonymous

  • 1 Answer

SOURCE: Kitchenaid K5A mixer 10 speed only runs on fast, no slow speed

Pull the back off and there will be two screws at the top of the Speed Control Plate and a 3rd screw at the bottom. Tighten the top two screws down. bakerboy49203@yahoo.com. Let me know if it works.

Posted on Mar 21, 2009

Anonymous

  • 135 Answers

SOURCE: KitchenAid 2671 onmly run Stir and Second at high speed

Hi. Goto kitchenaid.com and download the parts catalog for your mixer model, these drawings will assist you in the disassembly and reassembly of your mixer.

You'll need to replace the speed control in your mixer. This is a common problem. Be prepared to wait at least a month for your parts to arrive. Unplug your mixer before you open it up.

If you're still under warranty call kitchenaid!

If this solution has assisted you, please rate it. Good luck! ricardok45

Posted on Mar 21, 2009

Bob Hewitt

  • 130 Answers

SOURCE: Kitchenaid stand mixer will not stay in the off position.

There is a spring, item #4, which hooks on to the bottom of the control plate, item # 25, and pulls it back when you move the lever to off. Remove the rear cover and see if that spring is still connected to the control plate and to the lever arm, Item # 3. Here is the diagram:

http://shared.whirlpoolcorp.com/assets/pdfs/literature/Repair%20Part%20List%20-%208212369.pdf

Posted on Apr 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you fix a KitchenAid stand mixer speed ? Speed is only on high.


The speed selector may be defective and will have to be replaced.

Feb 10, 2018 | KitchenAid Food Mixers

1 Answer

Kitchen aid hd professional mixer problems with speed controls


you need a new speed control board, easy fix about $35.00 for the part and an hour of your time, not even messy to do a total of six screws and four wire connections that clip on, several youtube step by step instruction videos available. parts available on ebay. let us know if this helps you

Jan 28, 2013 | KitchenAid Food Mixers

1 Answer

Kitchenaid stand mixer KSM90EM turns off when going to the left on speeds 4 - 6. Makes a bit of noise at stir speed, but runs in time. Also noticed white dust powder in small amounts on the speed...


Get a Copy of the Repair Part List from Kitchenaid.com.
You need to adjust the mixer speeds:

Remove the screw holding the End Cover and locate the three screws from the Control Plate.
All three (2 top left and right, and 1 bottom) must be adjusted. Make sure that the Control
Plate is not damaged in any way, contacts are not charred or burnt,etc...

1. Loosen the lock nuts enough & Turn the 2 top screws clockwise until they cannot be turned
anymore. Leave the bottom screw alone for now.
2. Use a dab of white paint or paper whiteout to mark the positions of the Phillips screws.
3. Plug in your mixer and Set the speed selector to "Stir".
4. Turn each top screw One full turn couterclockwise (alternating between Left and Right)
Keep making one full turn at the time (for both left and right) until the motor starts running.
5. Put your hand near the Agitator shaft and allow it to brush your finger slightly. Use your
watch or clock and start counting the number of times the shaft touches your finger in
60 seconds. The correct count should be 60 RPM (Rounds Per Minute). If it is less
or more than 60, give each screw 1/4 turn counterclockwise or clockwise and start counting
again. Now tighten both lock nuts.
6. Set the speed selector to "6" and turn the bottom screw either clockwise or counterclockwise
to achieve a speed of 180 RPM.

For your reference, the planetary RPM's for the 5-qt. tilt-head Artisan Stand Mixer are as follows:
Stir speed - 60
Speed 2 - 95
Speed 4 - 135
Speed 6 - 180
Speed 8 - 225
Speed 10 - 280

Jul 30, 2011 | KitchenAid KSM90 Ultra Power Series Stand...

1 Answer

I have just purchased an ice cream freezer for my mixer. It is an older model and does not have a "stir speed" delineated. What is the equivalent of stir speed on the older models? -- 1 or 2?


On models with the "STIR" speed, the RPM (Rounds Per Minute) is 60.
Set your mixer speed to "1" or "2" and do the following:
Put your hand near the Agitator shaft and allow it to brush your finger slightly. Use your
watch or clock and start counting the number of times the shaft touches your finger in
60 seconds. In your case, the correct STIR speed is 60.

Jul 29, 2011 | KitchenAid KSM50PR Professional Series...

1 Answer

Kitchenaid speed controller (don,t work


You need to adjust the mixer speeds.
Obtain a copy of the KSM150PS Repair Part List from Kitchenaid.com.
Remove the screw holding the End Cover and locate the three screws from the Control Plate.
All three (2 top left and right, and 1 bottom) must be adjusted.

1. Loosen the lock nuts enough & Turn the 2 top screws clockwise until they cannot be turned
anymore. Leave the bottom screw alone for now.
2. Use a dab of white paint or paper whiteout to mark the positions of the Phillips screws.
3. Plug in your mixer and Set the speed selector to "Stir".
4. Turn each top screw One full turn couterclockwise (alternating between Left and Right)
Keep making one full turn at the time (for both left and right) until the motor starts running.
5. Put your hand near the Agitator shaft and allow it to brush your finger slightly. Use your
watch or clock and start counting the number of times the shaft touches your finger in
60 seconds. The correct count should be 60 RPM (Rounds Per Minute). If it is less
or more than 60, give each screw 1/4 turn counterclockwise or clockwise and start counting
again. Now tighten both lock nuts.
6. Set the speed selector to "6" and turn the bottom screw either clockwise or counterclockwise
to achieve a speed of 180 RPM.

For your reference, the planetary RPM's for the 5-qt. tilt-head Artisan Stand Mixer are as follows:
Stir speed - 60
Speed 2 - 95
Speed 4 - 135
Speed 6 - 180
Speed 8 - 225
Speed 10 - 280

Jul 20, 2011 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

Kitchenaid Artisan KSM150 Stir problem - Stir speed is the same as setting 2, but all others (4, 6, 8, 10) work fine. Tried adjusting the control board but "stir" and "2" still spin...


You are not adjusting the screws correctly. All three screws (2 top left and right, and 1 bottom)
must all be adjusted. Here is how:

1. Loosen the lock nuts enough & Turn the 2 top screws clockwise until they cannot be turned
anymore. Leave the bottom screw alone for now.
2. Use a dab of white paint or paper whiteout to mark the positions of the Phillips screws.
3. Plug in your mixer and Set the speed selector to "Stir".
4. Turn each top screw One full turn couterclockwise (alternating between Left and Right)
Keep making one full turn at the time (for both left and right) until the motor starts running.
5. Put your hand near the Agitator shaft and allow it to brush your finger slightly. Use your
watch or clock and start counting the number of times the shaft touches your finger in
60 seconds. The correct count should be 60 RPM (Rounds Per Minute). If it is less
or more than 60, give each screw 1/4 turn counterclockwise or clockwise and start counting
again. Now tighten both lock nuts.
6. Set the speed selector to "6" and turn the bottom screw either clockwise or counterclockwise
to achieve a speed of 180 RPM.

For your reference, the planetary RPM's for the 5-qt. tilt-head Artisan Stand Mixer are as follows:

Stir speed - 60
Speed 2 - 95
Speed 4 - 135
Speed 6 - 180
Speed 8 - 225
Speed 10 - 280



Jun 20, 2011 | KitchenAid KSM150PS Artisan Series Stand...

2 Answers

My KitchenAid mixer will not turn on. It was working fine, then it slowed down and made a noise as if it was being overworked, then it shut off. Now it is not turning on at all. The mixer has not been...


You may have to adjust the mixer speeds. Obtain a copy of the KSM150 Repair Part List from Kitchenaid.com. Remove the screw holding the End Cover and locate the three screws from the Control Plate. All three (2 top left and right, and 1 bottom) must all be adjusted. 1. Loosen the lock nuts enough & Turn the 2 top screws clockwise until they cannot be turned
anymore. Leave the bottom screw alone for now.
2. Use a dab of white paint or paper whiteout to mark the positions of the Phillips screws.
3. Plug in your mixer and Set the speed selector to "Stir".
4. Turn each top screw One full turn couterclockwise (alternating between Left and Right)
Keep making one full turn at the time (for both left and right) until the motor starts running.
5. Put your hand near the Agitator shaft and allow it to brush your finger slightly. Use your
watch or clock and start counting the number of times the shaft touches your finger in
60 seconds. The correct count should be 60 RPM (Rounds Per Minute). If it is less
or more than 60, give each screw 1/4 turn counterclockwise or clockwise and start counting
again. Now tighten both lock nuts.
6. Set the speed selector to "6" and turn the bottom screw either clockwise or counterclockwise
to achieve a speed of 180 RPM.

For your reference, the planetary RPM's for the 5-qt. tilt-head Artisan Stand Mixer are as follows:
Stir speed - 60
Speed 2 - 95
Speed 4 - 135
Speed 6 - 180
Speed 8 - 225
Speed 10 - 2

Jun 10, 2011 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

KitchenAid 2671 onmly run Stir and Second at high speed


Hi. Goto kitchenaid.com and download the parts catalog for your mixer model, these drawings will assist you in the disassembly and reassembly of your mixer.

You'll need to replace the speed control in your mixer. This is a common problem. Be prepared to wait at least a month for your parts to arrive. Unplug your mixer before you open it up.

If you're still under warranty call kitchenaid!

If this solution has assisted you, please rate it. Good luck! ricardok45

Jan 28, 2009 | KitchenAid KP26M1X Stand Mixer

1 Answer

Kitchenaid 250 watts k4ss mixer


The repair manual says that the mixer can make this grinding sound at slow speed, like stir or 2. This is normal, especially until it warms up. This is the sound of the gears turning at slow speed.

Dec 13, 2007 | KitchenAid K45SS Classic Stand Mixer

Not finding what you are looking for?
KitchenAid KSM150PS Artisan Series Stand Mixer Logo

Related Topics:

497 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Food Mixers Experts

Appliance engineer

Level 2 Expert

194 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a KitchenAid Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...