UPGRADE Hello, I have a Soltek SL-65KV2-CT - motherboard - ATX - Pro133T working with the Intel Pentium III SL3VG (600 MHz) and 128 MB 133Mhz SDRAM PC133 DIMM 168PIN RAM. it's working slow but it works ! I would like to know if i can simply substitut the 128 MB ram memory for 3 * 512 MB (1,5 GB) and the SL3VG for one of this processors: Intel Pentium III 1.40GHz 133MHz FSB 512KB Processor (Intel P3 Tualatin model SL6BY) or Intel Pentium III 1.40GHz 133MHz FSB 512KB Processor (Intel P3 Tualatin model SL5XL) Thanks

Up to Pentium III/M 600 MHz

you can check out this web site.
http://www.tigerdirect.com/

Here is Windows Xp requirements:
PC with 300 megahertz or higher processor clock speed recommended; 233 MHz minimum required (single or dual processor system);* Intel Pentium/Celeron family, or AMD K6/Athlon/Duron family, or compatible processor recommended
128 megabytes (MB) of RAM or higher recommended (64 MB minimum supported; may limit performance and some features)
1.5 gigabytes (GB) of available hard disk space*
Super VGA (800 x 600) or higher-resolution video adapter and monitor
CD-ROM or DVD drive
Keyboard and Microsoft Mouse or compatible pointing device

it's 100 other info as follows:

Component Attributes RAM (standard) 64 MB SDRAM standard Maximum 256 MB (2 x 128 MB DIMM) Speed 100 MHz synchronous Sockets Two 168-pin DIMMs Size 16, 32, 64, and 128 MB DIMMs Type Supported SDRAM, 100 MHz, Intel PC SDRAM unbuffered DIMM specification, revision 1.0 compliant
Cache Level Quantity Level 1 (Primary) 32 KB (on processor) Level 2 128 KB (on processor) Upgrade Sockets None

That is because your system does not meet the minimum requirements to enable it. Your prblem is with the graphics adapter agp - Axcellerated Graphics Port, YOu will need to have a compatable Graphics Card to do it along with a processor at least 1.66 ghz

hi dear
there is always speed mismatch problem occur when we use low processor & high ram

so try to use 256 ram
also try to use 1 slot of 256 ram & 2 slots of 128 ram diffrently
& compare the speed
hope it will help to u

The motherboard has three, dual in-line memory module (DIMM) sockets. Minimum memory size is 16 MB; maximum memory size is 768 MB. The largest DIMM supported at this time is 256 MB using unbuffered 128 Mbit technology parts. The BIOS automatically detects memory type, size, and speed.

The motherboard supports the following memory features:

• 168-pin DIMMs with gold-plated contacts
• 66 or 100 MHz SDRAM
• Non-ECC (64-bit) and ECC (72-bit) memory
• 3.3 V memory only
• Unbuffered Single- or double-sided DIMMs in the following sizes:

DIMM Size Non-ECC Configuration ECC Configuration 16 MB 2M x 64 2M x 72 32 MB 4M x 64 4M x 72 64 MB 8M x 64 8M x 72 128 MB 16M x 64 16M x 72 256MB 32M x 64 32M x 72

Synchronous DRAM (SDRAM) can be installed in one, two, or three sockets. EDO DIMMs are not supported. Memory size and speed can vary between sockets.

Note: Intel® Pentium® II processors with 100 MHz front-side bus should be paired only with 100 MHz SDRAM. Processors with 66 MHz front-side bus can be paired with either 66 MHz or 100 MHz SDRAM.

All memory components and DIMMs used with the Intel® SE440BX-2 motherboard should comply with the PC SDRAM specifications. These include: the PC SDRAM Specification (memory component specific), the PC Unbuffered DIMM Specification, and the PC Serial Presence Detect Specification.

Note: It is recommended that SPD memory DIMMs be used with the SE440BX-2 motherboard. However, the BIOS will allow the use of non-SPD DIMM memory.

So the max you can go is 3 x 256 MB.

Thanks and please take a moment to rate fixya.

yes i told you that but i change my mind
throw your computer upside down
and after that buy my computer

Pentium 1 75 mghz
24 mb ram
640 mb hdd
1mb vga

http://www.updrivers.com/bios/Motherboard/Soltek/12/313/page2.html

Please vote!

It is listed here for bios, only site left. Can't find drivers.
http://www.updrivers.com/bios/Motherboard/Soltek/12/313/page2.html