At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Hello there: If the washer leaks all the time, check these:Hot and cold water fill hoses - Check the hot and cold
water hoses from the household plumbing. If either hose is leaking,
tighten it or replace it, as appropriate.Main tub seal - The main tub seal is located between
the transmission and the outer tub. It's the primary water seal in the
outer tub for the transmission-shaft entry point. If this seal leaks,
you can see the leak by opening up the machine's main access panel while
the machine is full of water with a small amount of detergent in it.
The leak appears at the underside of the outer tub, at or near the
center. This seal is difficult to replace. You probably should call a
qualified appliance repair technician. Pump - If the pump leaks, you can probably spot the
leak when the tub is full of water. The pump has two or more black
rubber or plastic hoses attached to it and usually has a drive belt that
spins the pump. If the pump is leaking, you need to replace it. Outer tub - Over time, the steel or plastic outer tubs
can rust, split, or be punctured. If this happens, you may have to
replace the entire outer tub-
Hi If your washer leaks every time you run it, then check these:
Hot and cold water fill hoses - Check the hot
and cold water hoses from the household plumbing. If either hose is
leaking, tighten it or replace it, as appropriate.
Main tub seal - The main tub seal is located
between the transmission and the outer tub. It's the primary water seal in
the outer tub for the transmission-shaft entry point. If this seal leaks,
you can see the leak by opening up the machine's main access panel while
the machine is full of water with a small amount of detergent in it. The
leak appears at the underside of the outer tub, at or near the center.
This seal is difficult to replace.
Pump - If the pump leaks, you can probably
spot the leak when the tub is full of water. The pump has two or more
black rubber or plastic hoses attached to it and usually has a drive belt
that spins the pump. If the pump is leaking, you need to replace it.
Outer tub - Over time, the steel or plastic
outer tubs can rust, split, or be punctured. If this happens, you may have
to replace the entire outer tub--but that may not be an economical repair
to make.
Please rate the solution if you find it useful and helpful.
Air-gap device -The air gap is a small device found on most washers that prevents the wash water from being siphoned into the household water supply. It's located either mid-way along or at the end of the black rubber hose that comes from the water-inlet valve. Often it's made of translucent plastic. If one of the air-gap components deforms or cracks, you may need to replace it.
The tube -There's a rubber tube that runs between the water-inlet valve and either the air-gap or the inlet spout. If it cracks or breaks, it can cause a leak.
Inlet spout -Most washers have a plastic spout near the top of the main clothes tub that directs the water into the tub. If the spout cracks or breaks free of its mounting, it can cause a leak.
During drain and spin only
A washer that leaks only during the spin cycle often has a leak in the main drain hose. Inspect the entire hose and correct any problem you find. Alternatively, the steel or plastic outer tubs can rust, split, or be punctured. This may be most visible during large loads and high water levels. If this happens, you may have to replace the entire outer tub--but that may not be an economical repair to make. Consult a qualified appliance repair technician for further details.
All the time
If the washer leaks all the time, check these:
Hot and cold water fill hoses - Check the hot and cold water hoses from the household plumbing. If either hose is leaking, tighten it or replace it, as appropriate.
Main tub seal - The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft entry point. If this seal leaks, you can see the leak by opening up the machine's main access panel while the machine is full of water with a small amount of detergent in it. The leak appears at the underside of the outer tub, at or near the center. This seal is difficult to replace. You probably should call a qualified appliance repair technician.
Pump - If the pump leaks, you can probably spot the leak when the tub is full of water. The pump has two or more black rubber or plastic hoses attached to it and usually has a drive belt that spins the pump. If the pump is leaking, you need to replace it.
Outer tub - Over time, the steel or plastic outer tubs can rust, split, or be punctured. If this happens, you may have to replace the entire outer tub--but that may not be an economical repair to make. Consult a qualified appliance repair technician for further details.
Hi, i wouldfirst check the water valve assembly and all inlet hoses as well. make sure they are secure and tightly screwed onto there respective connections. if all the hoses are good and the water valve isn't leaking, it will be the tub seal. you will have to replace this rubber o ring seal.
You'll need to open the machine and check for the leaks in the hose connected to the drain pump. Also check if the clamp connecting the drain filter and hose is tight. Also check these things for leaks---
Main tub seal - The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft entry point. If this seal leaks, you can see the leak by opening up the machine's main access panel while the machine is full of water with a small amount of detergent in it. The leak appears at the underside of the outer tub, at or near the center. This seal is difficult to replace.
Pump - If the pump leaks, you can probably spot the leak when the tub is full of water. The pump has two or more black rubber or plastic hoses attached to it and usually has a drive belt that spins the pump. If the pump is leaking, you'll need to replace it.
Please do rate this solution as FixYa if found useful and revert for further assistance.
Bosch Nexxt 500 WFMC3301 Front Load Washer how to get the metal ring back on. This video will show you how to change a door seal on this Bosch front loader washing machine and also how to replace the metal rings. we have all bosch repairs in our channel. Please remember to subscribe to our YouTube channel for all appliance tutorials a 4 THUMBS rating is appreciated for answering your FREE question.
It leaksYour washer can develop several types of leaks. You can track down a leak based on when it occurs:
During fill only During drain and spin only All the time
During fill only If the washer leaks only during the fill cycle, check these:
Air-gap device -The air gap is a small device found on most washers that prevents the wash water from being siphoned into the household water supply. It's located either mid-way along or at the end of the black rubber hose that comes from the water-inlet valve. Often it's made of translucent plastic. If one of the air-gap components deforms or cracks, you may need to replace it.
The tube -There's a rubber tube that runs between the water-inlet valve and either the air-gap or the inlet spout. If it cracks or breaks, it can cause a leak.
Inlet spout -Most washers have a plastic spout near the top of the main clothes tub that directs the water into the tub. If the spout cracks or breaks free of its mounting, it can cause a leak.
During drain and spin only A washer that leaks only during the spin cycle often has a leak in the main drain hose. Inspect the entire hose and correct any problem you find. Alternatively, the steel or plastic outer tubs can rust, split, or be punctured. This may be most visible during large loads and high water levels. If this happens, you may have to replace the entire outer tub--but that may not be an economical repair to make. Consult a qualified appliance repair technician for further details.
All the time If the washer leaks all the time, check these:
Hot and cold water fill hoses - Check the hot and cold water hoses from the household plumbing. If either hose is leaking, tighten it or replace it, as appropriate.
Main tub seal - The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft entry point. If this seal leaks, you can see the leak by opening up the machine's main access panel while the machine is full of water with a small amount of detergent in it. The leak appears at the underside of the outer tub, at or near the center. This seal is difficult to replace. You probably should call a qualified appliance repair technician.
Pump - If the pump leaks, you can probably spot the leak when the tub is full of water. The pump has two or more black rubber or plastic hoses attached to it and usually has a drive belt that spins the pump. If the pump is leaking, you need to replace it.
Outer tub - Over time, the steel or plastic outer tubs can rust, split, or be punctured. If this happens, you may have to replace the entire outer tub--but that may not be an economical repair to make. Consult a qualified appliance repair technician for further details.
Air-gap
device -The air gap is a small device found on most washers that
prevents the wash water from being siphoned into the household water
supply. It's located either mid-way along or at the end of the black
rubber hose that comes from the water-inlet valve. Often it's made of
translucent plastic. If one of the air-gap components deforms or
cracks, you may need to replace it.
The tube -There's a
rubber tube that runs between the water-inlet valve and either the
air-gap or the inlet spout. If it cracks or breaks, it can cause a
leak.
Inlet spout -Most washers have a plastic spout
near the top of the main clothes tub that directs the water into the
tub. If the spout cracks or breaks free of its mounting, it can cause a
leak.
During drain and spin only
A
washer that leaks only during the spin cycle often has a leak in the
main drain hose. Inspect the entire hose and correct any problem you
find. Alternatively, the steel or plastic outer tubs can rust, split,
or be punctured. This may be most visible during large loads and high
water levels. If this happens, you may have to replace the entire outer
tub--but that may not be an economical repair to make. Consult a
qualified appliance repair technician for further details.
All the time
If the washer leaks all the time, check these:
Hot
and cold water fill hoses - Check the hot and cold water hoses from the
household plumbing. If either hose is leaking, tighten it or replace
it, as appropriate.
Main tub seal - The main tub seal
is located between the transmission and the outer tub. It's the primary
water seal in the outer tub for the transmission-shaft entry point. If
this seal leaks, you can see the leak by opening up the machine's main
access panel while the machine is full of water with a small amount of
detergent in it. The leak appears at the underside of the outer tub, at
or near the center. This seal is difficult to replace. You probably
should call a qualified appliance repair technician.
Pump
- If the pump leaks, you can probably spot the leak when the tub is
full of water. The pump has two or more black rubber or plastic hoses
attached to it and usually has a drive belt that spins the pump. If the
pump is leaking, you need to replace it.
Outer tub -
Over time, the steel or plastic outer tubs can rust, split, or be
punctured. If this happens, you may have to replace the entire outer
tub--but that may not be an economical repair to make. Consult a
qualified appliance repair technician for further details.
Goodluck, Please don't forget to rate the solution
Your leak could be coming from the rubber door seal. Inspect all the way around the rubber seal paying particular attention to the areas behind the rubber seal where it meets the wash tub. They wear with age and can develop small holes. When they start leaking it appears like water coming from under the machine. I hopes this helps.
×