Vehicle Parts & Accessories Logo

Related Topics:

Posted on Nov 19, 2009
Answered

Ford factory installed remote start I open door and truck shuts off what can I do to program this so it works like it should

Answer This Question

5 Answers

Anonymous

Level 1:

An expert who has achieved level 1.
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
New Friend:

An expert that has 1 follower.

  • Contributor 7 Answers
  • Posted on Nov 28, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
New Friend:

An expert that has 1 follower.

Joined: Nov 25, 2009
Answers
7
Questions
0
Helped
9461
Points
38

Follow the following procedures for 2010 Ford vehicles with the door open shut down enabled:

1. Locate the override button and LED. On my escape the override button was at the bottom of the plastic by the driver's knees. The LED is attached to the harness behind this plastic, under the steering column. It is easier to find it once it's on.

2. Open the driver's door, press and hold the brake, turn the vehicle on.

3. While holding the brake, press and hold the override button, after 10-15 seconds the horn will honk 3 times. Let go of the button and the brake.

4. Push the override button until you hear the horn honk 5 times.

5. Push the brake until the horn honks 7 times, this is the "door open shut down" selection. The LED should be on.

6. Push the start button on the Key Fob. Do NOT hold it down, or it will reset everything.

7. The LED should now be off.

8. Shutdown the vehicle, and test it out.

Note: This procedure can be used to change the auto shut-off from 10 to 15 minutes as well. Instead of going to where the horn honks 7 times, go to where it honks 3 times, and turn the LED on.

Anonymous

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 1 Answer
  • Posted on Dec 17, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Mayor:

An expert whose answer got voted for 2 times.

Joined: Dec 17, 2009
Answers
1
Questions
0
Helped
7983
Points
7

Thanks Roymoney! It worked like a charm! The override button was difficult to find on my 2010 Expedition Limited - it was taped to a wire harness under the dash between the power brake module and the emergency brake mechanism. I could not see an LED, but it doesn't matter. You need to push and release the override button (#4) several times to get the 5 honks - same with the brake - first time, one honk, second time, 2 honks, etc. Thanks again!

Ad

Anonymous

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 1 Answer
  • Posted on Apr 01, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Mayor:

An expert whose answer got voted for 2 times.

Joined: Apr 01, 2010
Answers
1
Questions
0
Helped
7983
Points
2

I can get into the option banks but when I change option bank 2 - menu 7 - my 2010 f150 won't start via rmst. Instead of the engine turning over and starting, it honks 5 times (meaning key in the ignition error). Any suggestions?

kjb451

kjb451

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Oct 31, 2012
kjb451
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Oct 31, 2012
Answers
1
Questions
0
Helped
7983
Points
0

My 2010 F150 Platinum security light blinks when I try to start the truck. Can this be fixed at home or do I need to take it to service?

Anonymous

Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Corporal:

An expert that has over 10 points.

  • Contributor 1 Answer
  • Posted on Jun 09, 2013
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
New Friend:

An expert that has 1 follower.
Corporal:

An expert that has over 10 points.

Joined: Jun 09, 2013
Answers
1
Questions
0
Helped
7983
Points
20

I need a licence for PC UTILITY

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I assume the factory alarm was somehow bypassed when they installed the remote start is there a way I can make the factory alarm work when the doors are opened without key,?
To arm content theft alarm.
1. Open the door.
2. Lock the door with the power door lock switch or
the remote keyless entry transmitter. The
SECURITY light should flash.
3. Close all doors. The SECURITY light should go off
after approximately 30 seconds. The alarm is not
armed until the SECURITY light goes off.

If a locked door is opened without the key or the remote keyless entry transmitter, the alarm will go off. The headlamps and parking lamps will flash for two minutes, and the horn will sound for 30 seconds, then will turn off to save the battery power.
Read full answer
Jun 24, 2021 • GMC Cars & Trucks
0helpful
2answers

Changed battery and now remote doesn't work. it is on a 2005 ford freestyle
press the helpful button,there appears there is more then one type of remote, I think one has auto start and one does not.

owners manuals in the glove box and in there was the Ford Auto Start Remote booklet. For those of you who need to program a new auto start remote, you turn the ignition to the on position, push and hold the little over-ride button (mine is down on the left side kick plate near the hood release) for about 15 seconds, you will hear a chirp which means the system is ready to be programmed, just hit the lock key on your remote and the system will chirp acknowledging the remote has been programmed, continue to do this will all other remotes you have within I believe it was 20 seconds - then shut off the ignition and test your remotes. Worked perfectly for me.
OR

Free Do It Yourself instructions from your friends at Lessco Electronics

1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds press any button on first keyless remote. Door locks will cycle to confirm programming.

3. Within 20 seconds, press any button on second keyless remote. Door locks will cycle again to confirm programming.

4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
Link below
2005 2006 Ford Freestyle Factory Transmitter Remote Fob Programming
Read full answer
Jan 26, 2016 • Ford Cars & Trucks
0helpful
1answer

Factory remote start wont work. hit button horn bbeps all lights and radio come on. when horn beeps second time car wont crank as it always has in the past

Ford Keyless Remote Car Starter fix - YouTube

? 5:14
https://www.youtube.com/watch?v=fQHb0mU0rvI
Jun 24, 2012 - Uploaded by mitch cox
I bought a 2010 Ford Raptor my remote starter won't work? when I press the .... 2013 lincoln navigator, 2-Way Remote StartSystem and i press button ... a Ford OEM 1-Way 100 Series Keyless Remote Start (CM5Z-19G364-A).

1998 to 2008 Lincoln Navigator Factory Transmitter Remote ...

? 3:00
https://www.youtube.com/watch?v=sLMN34KN3nY
Nov 2, 2012 - Uploaded by Lessco Electronics
1. Close all doors and then open drivers door and press the UNLOCK button on drivers door panel while door ...

2008 Lincoln Navigator Remote Start Accessories ' Th




Read full answer
Dec 12, 2015 • 2008 Lincoln Navigator
0answers

When i push the remote start my 2009 Ford Escape beeps and the lights flash and the horn beeps as normal but then the truck does not start but the lights all flash and then the horn goes 4 times but i
Read full answer
Be the first to answer Jan 07, 2015 • 2009 Ford Escape
0helpful
2answers

I have a ford explorer 1994 i lost the control remote, Installed a new alarm, but technician can not uninstall the factory alarm How can I do this? when new alarm is on, and opened the doors whit new...
Why not just get the factory PATS System working correctly. You can't remove the factory system,it's an integral part of you vehicles systems and processors

You can get new remotes and program them!!
Read full answer
May 26, 2010 • 1994 Ford Explorer Limited
5helpful
1answer

Program a new fob to my 2002 f150 supercrew lariat 5.4L remote lock/start system
if it is a ford remote or ford factory alarm remote cycle the key from off to run(usually 8 times) untill you hear door locks activate. at this exact time key needs to be in the on position.touch unlock or lock on all remotes being programmed and make sure door locks respond to remotes. then turn key off ending programming mode.then try your fobs they should work
Read full answer
Nov 06, 2009 • 2002 Ford F150 Regular Cab
0helpful
1answer

1994 Ford f250-Remote key pad won't unlock doors so opened with
You have an aftermarket alarm (factory system did not have a "valet switch") Have it removed or replaced.
Read full answer
Oct 24, 2009 • 1994 Ford F250 Supercab
2helpful
2answers

Ford F150 remote key does not work after car battery
cbridges2232,

Any luck with your keyless remote issue? I'm having the exact same problem with my Ford F150 CrewCab after car battery replacement.
Read full answer
Oct 07, 2009 • 2001 Ford F150 Styleside SuperCrew
0helpful
1answer

My keyless entry remote stopped working so i had unlock the door through a cracked window.... the alarm went off, but when i started it, the alem didnt stop.... now when i dont lock it and open the door or...
yes the remotes do have batteries. how ever that might be your problem or the remotes lost its code for programing. step when turning alarm off---- if its a factory alarm put the key in the drivers door when the door is closed and lock then unlock it thats the manuel shut down for factory. step 2------- aftermarket alarm. look for a valet switch most likely it would be installed by the driver kick panel or by the under dash fuse box. when u find it put the key into the ignition. turn it to the run position. within 3 seconds press and hold the valet switch for 3 to 5 seconds you should here a confirmation chirp and the led light will stay on solid and wont blink give it a world let me know what happens
Read full answer
Jun 10, 2009 • 1999 Oldsmobile Aurora
0helpful
1answer

Program my remote
Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entrymag-glass_10x10.gif, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.
  • Open the driver's door. Remove the key from the ignition switch.
  • (Complete these steps within 40 seconds)
    1. Insert the key into and remove it from the ignition switch 2 times.
      (IN - OUT - IN - OUT)
    2. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    3. Insert the key into and remove it from the ignition switch 1 time.
      (IN - OUT)
    4. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    5. Insert the key into the ignition switch and leave it in.
    6. Close the driver's door.
    7. Turn the key from LOCK to ON 4 times, ending at LOCK
      (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
    8. Wait for the locks to stop, then remove the key from the ignition switch.
  • On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
    1. [For all doors unlock] press and release the UNLOCK button.
    2. [For driver door unlock] press and release the LOCK button.
  • Open the driver's door. The programming is complete. If programming did not occur, start over.
Read full answer
Jan 13, 2009 • 2001 Toyota Tacoma
Not finding what you are looking for?

View Most Popular

Vehicle Parts & Accessories

Related Question

I assume the factory alarm was somehow bypassed when they installed the remote start is there a way I can make the factory alarm work when the doors are opened without key,?

  • GMC Cars & Trucks

7,993 views

Ask a Question

Usually answered in minutes!

Popular Questions

How do i remove the cover of a honeywell home

Code-Alarm Code Alarm Transponder

Need a picture of a ford 2000 xr6 falcon fuse box diagram

2004 Mustang Factory Wiring Diagrams

Opel corsa 1.4i firing order

2004 Mustang Factory Wiring Diagrams

Ford transit lock problem

Code-Alarm Code Alarm Transponder

How can I disarm the anti-theft alarm on my 2004 Ford Escape?

Accessories Alarm Siren

Top Ford Vehicle Parts & Accessories Experts

xxxxxx xxx

Level 3 Expert

5117 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Are you a Ford Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...