I have the radion shack hdtv remote. Cat no
Download the manual and codes from here
http://www.remotecentral.com/cgi-bin/files/dl.cgi?file=others/radio_shack/15135-manual.zip&area=other
Here is how to set the code...
1. Turn TV on
2. Press TV button on remote
3. Hold P button on remote until LED blinks twice
4. Enter the first 5 digit code for Magnavox TV's
5. Press Power button - TV should turn off. If TV doesn't turn off repeat steps 2-5 with the next 5 digit code, until either TV goes off or run out of codes.
6. If out of codes use searching for code method below...
TV codes for Magnavox
10047, 11454, 10054, 10154, 10000, 10250, 10051, 10180, 10060, 10030, 10171, 10092, 10706, 11913, 11904, 11755, 10019, 11365, 11254, 10802, 10386, 10282, 10020, 10187, 10186, 10024, 10179, 10096
Searching for code
1. Turn on TV.
2. Press TV button on remote
3. Press and hold P button until LED blinks twice
4. Enter code 991 on remote - LED blinks twice
5. Press 1 - Device key blinks twice
6. Press Power button once
7. Press and release CH+ key until TV turns off.
At this point in the manual, the manual is only correct depending on what type of TV you have.
In the manual if you press the Power on button the TV should turn itself back on, the fail to state that not all TV's turn on by the power button, the majority now are triggered to turn on, on channel change, however you can't use channel change here to check it as you'll go to the next code... here is my solution...
8. Turn TV back on either using original TV remote, or buttons on front (most TV's if you change channels they come back out of standby mode, very few now turn on by pressing the power button).
9. Press Power button on remote - TV should turn itself off again.
10. Press P button on remote to lock in that code.
If the device does not turn off press CH- to go back through the codes, press and release P button when TV turns off.
Finding code
If you used the search function you might want to know what code it's using. To do this follow these instructions...
1. Press TV button
2. Press and hold P until LED blinks twice
3. Enter 990 and LED blinks twice
4. Press 1 and count number of times LED blinks this is the first digit of your code (e.g. 1 blink = 1, 2 blinks = 2, etc).
5. Repeat step 4 pressing buttons 2 - 5 for the other digits (e.g. for the second digit press 2 count number of blinks.. etc)
At this point the manual doesn't tell you how to get out of this mode, I presume pressing any other button on the remote other than 1-5 will take you out of this mode, either that or leaving the remote alone for 5 minutes.
when i push the button to turn my tv on it blinks 3 times then shuts off.it will not turn on.
the power buton blinks red and gren and it dos"t turn on. What can i do
I have Toshiba 43HX71 rear projection TV. It was turned on and all appeared normal when the picture disappeared and power light began blinking continuously. The TV can not shut down (i.e. to stop the blinking) using the power button, but must be unplugged.
This is the second time this has occurred. The first time, about 2 months ago, I was able to get it working again by unplugging the TV and all inputs from the rear panel, then plugging the TV in again, testing to see that it could be powered back on without resuming the blinking, and finally re-connecting all the input sources. The same process is not working this time.
Does anyone know what causes this and how much it will cost to fix before I spend the $$ to have a tech tell me to junk it?
Greeb light flashes and the red light is on...... Wont turn on???
the tv won't turn on. The light around the power button flashes several times; then stops. tv never turns on.
The picture looked like an over-exposed photo. I turned off the tv and can't the tv to turn on.
I've unplugged the unit from the wall socket, waited two hours and replugged. No result.
I can not get my tv to turn on. The green light blinks 3 times then nothing.
My Tv does the same thing. When I try to turn it on the red light blinks and the tv "churps" at me. Anyone know what that churping noise is?
I press the power button and the green light blinks three times and then....nothing. I need help!!
tv will not turn on. red like blinks.
Try to turn on my Rca D52w20 It blinks 3 times like its trying to turn on and then shuts off the first couple of times it sizzles it sat for a couple of weeks and I tried it again it work all day then at night it sizzled and shut off, is it the regulaor box if so how is it to box on this TV? ,,,,Thanks for any help!
The TV just cut off. When I tried to turn it back on the green light came on then off. Then it blinked 3 times. Do I need a new TV
we have the same problem. one day it went off. the power button won't turn on to red, it flashes to yellow and then goes blank. no sound , no picture. nothing.
will not turn on, when power button is pressed light blinks 3 times and occasionally it will turn on after several tries.
I have a RCA D52W20 52 Inch projection tv and it will not turn on. The power button flashes on and off 3 times and I here a clicking noise when it flashes but it will not turn on. PLEASE HELP!!! THANKS IN ADVANCE!!!!
I have the same problem. Replaced the flyback and the three problem prone capacitors, and still doing the same thing. 3 blinks and the micro processor shuts the tv off??????????????? Paid alot for this t.v. Throwing in the dump, no more rca products for me.
Light blinks and turns off
My local radio shack only has huge capacitors (with the same rating) in comparison to the ones that rca used. Â Will this make a differace? Â Thanks
×