Question about Plumbing

1 Answer

How to install a faucet in the tub? - Plumbing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 30,351 Answers
Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hydrabath tub


I suppose you intend to install the faucets on the hydrabath tub. There should not be any restriction to the choice of faucets as long as they fit into the location and situation of use.

Feb 23, 2014 | Plumbing

1 Answer

Copper piping? Tub faucets


1. Measure piping size with tape measure or read printed on pipe. 2. Visit local hardware store and take the faucet. 3. Tell them you need a tubing cutter and sharkbite adapters for the faucet you have. 4. Cut pipe with tubing cutters. 5. Push on sharkbite fittings. 6. Install faucet and supply hoses. 7. Take Bath.

Apr 28, 2013 | Plumbing

1 Answer

I would like information on steps to remove bathtub and install pre fab shower


This is a fairly big job but can be done if you have the right tools and a little bit of time....... Depending on the existing tub material (cast iron,fiberglass, tin type ). You will want to remove faucet trim(handles,spout) first. Then the over flow plate on tub,as well as drain in the bottom (this will require a drain removal wrench or pair of needle nose pliers and screw driver, and some strong arms).After this is done remove tub unit , if the unit is a cast iron unit a good sledge hammer will work as you will need to break into halves to remove unless your trying to save tub and provided you can then get the unit out the door in one piece...... Caution, protect body and eyes in this process, flying pieces of cast iron can do some damage to body......cutting tub will take several blades and take quite a while to do......The next step depends on the location of faucet and if you are replacing the tub faucet or going to use the existing faucet.... I would recommend a new faucet because if this is going to be a shower only you may want to raise the faucets so they will be easy to operate without having to bend..Depending on the model pre-fab (two piece,three piece) unit you wish to install you may need to prep the drain to make sure it will fit your new installation. Let me explain... most tubs have the drain located at the right/left end of tub and the showers are located in the center of the unit thus leaving you to relocate the drain. If house is on slab it means a little jack hammering the concrete to provide this, if the floor is a conventional it means re-routing the drain to the center.......once all this is accomplished you are ready to install unit base,connecting drain. Next you need to get the faucet located to the right height or be able to get to the back side of the shower and remove the existing faucets and replace them after you install surround.....turn off water supply before removing faucet..... A sturdy surround will make for a less involved support system around shower area.Be sure to leave enough space between studs for faucet attachment. Sounds like a lot of work and it is but after its done you will have a great bath shower..... hope this was helpful.... sorry this only dealt with the plumbing aspects of the job......

Sep 05, 2011 | Home

1 Answer

Set screw is stuck. Any suggestions on how to remove it to replace the roman tub faucet?


to replace the roman tub faucet you have to expose the faucet under the deck of the tub. Most of the time builders do not install a door to do repairs. So expose the underside of the deck of the tub, turn off the main water outside then cut the water pipe for the hot and cold water with a tube cutter. At this point take a sawall and place the blade so the side of the blade touches the bottom side of the deck.
and cut all the way though the body of the stem.

Do all three and your done with the hard part. Install your new faucet and enjoy.

Hope I was help to you Rich

Sep 05, 2011 | Moen T999/4999 Chateau Two Handle Roman...

1 Answer

Installed a new tub faucet and I have no water coming out of it


When you turned off the water to remove the old faucet did you have to turn off the water to the whole house or was there cut off valves going to the tub. Did you install cut off valves for the tub and forgot to turn them back on before trying the new faucet. What type of faucet did you install? Whats the make and model. Its possible something got caught/dropped in the pipe when you were installing the new faucet and is now blocking the flow of water.

Jul 25, 2011 | Plumbing

1 Answer

On new Moen shower faucet, when I turn on faucet, water drips from shower also.


The faucet was installed upside down.
The shower riser pipe in the wall is to short( the distance between the faucet and shower head).
One of the biggest problems is if your shower faucet was installed with Pex pipe to the tub spout. Pex pipe will restrict the flow and force the water back up and out of the shower head.
The tub spout must be piped with at least 1/2 brass pipe nipples and fittings, or 5/8 OD. copper pipe and fittings.
Hope this helps, if you further questions please let us know.

Sep 08, 2010 | Moen 3175 Legend One Handle Shower Faucet...

1 Answer

I am haveing a problem putting my tub and shower faucet back need a daigram of it can find one online it is a delta tub and shower faucet can you help me james


The only thing that comes to my mind, go back where you bough them and
ask them to make some copies of the installation instruccions.
I know...the pride will get hurt a bit....but you will install this bath in NO time.
Hope this help

Mar 26, 2010 | Delta Faucet Peerless& Single Handle...

Not finding what you are looking for?
Plumbing Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plumbing Experts

Brad Brown

Level 3 Expert

18136 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you a Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...