Question about Onkyo Audio Players & Recorders

Hi! my name is Arthur. I have Onkyo nr 545 . Problem is Det.Protect: I I probaly connect speaker after circuit +and- speaker cabel beetween . Can you help me

1 Answer

Ambrosia Heart

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Loyalty:

Visited the website for 30 consecutive days.
Expert
130 Answers

You have already pointed out the problem:
Problem is Det.Protect: I.
How to fix :
(1)download 545/535/525 service manual.
(2)check all power transistors CE & BE resistances
if theyy are very low ,0 ohm, or infinity.
(3)check all 0.22 ohm resistors if they are open
or turning greater.
(4)Check the biasing circuit with a small rating
transistor and an orange color variable resistor.
(5)Check all channels.

Posted on Oct 17, 2019

5 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Anonymous

1 Answer

SOURCE: onkyo ht-r500 no speakers attached goes directly

I have a HT-R520 - First thing stated in the manual is 'Do Not Apply Power to the System Until All the Speakers Are Connected to the Receiver.' This practice avoids any hot connects to the speakers. As with any high-outpiut system connecting spreaker wires to the system while in operation can spike the speakers as well as the amplifier curcuits. Hook up your speakers first and give it a try. Good Luck!

Posted on Aug 20, 2009

Anonymous

132 Answers

SOURCE: I have a new house that had speakers built into

you can check them with a ohm meter, hook it to the wires that you hook to the reciever and if you get a reading it is good if no reading it is bad wires

Posted on Nov 22, 2009

Mical Caterina

3400 Answers

SOURCE: I have four Bose 161 speakers and an Acoutismass 5

you're going to need a ohm meter (good electrical testers have them) and make sure ohm ratings from speakers match the ratings for your receivers. Sounds like to much resistance for receiver(s)

Posted on Jan 06, 2011

Rommel Cana

5807 Answers

SOURCE: Onkyo 545 one channel don't work

Use headphones or Computer Speakers
and plug in to your headphones jack.

If the audio is present on both channel , check your speaker system

or the jack circuits.

If symptoms are the same, follow the troubleshooting on the link

above.

Posted on Oct 10, 2012

Add Your Answer

Upload

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

I have a onkyo tx-nr828 that will not power on

To check protect mode: what kind of protection it belongs to when NG channel is displayed such:
NG:LCRSLSRBLBR
NG__CH:LCRSLSRBLBR
1.Press the Enter button
2.Protect cause are displayed for 5 seconds.
DET.PROTECT:I(overcurrent)
DET.PROTECT:V(dc detected)
If warranty still have,call onkyo to repair.
Search you tube SR600 cap replacement and send an email to me, if you want to repair it by yourself.

Oct 04, 2017 | Onkyo Audio Players & Recorders

3 Answers

My onkyo tx-rz810 keeps going toDet.pretction mode how do I get it out of that mode

Does the display show you are in protect mode , or is a light indicating that? The unit automatically switches to standby when the
"Hardware" - "Power Management" - "Auto Standby"
setting in the Setup menu functions are set. The protective circuit function may have been activated.
If this has occurred, "AMP Diag Mode" appears on the
display when the unit is turned on again, and the unit
enters diagnostic mode. If the results of the diagnosis is
that there is no problem, the "AMP Diag Mode" display
disappears and you can use the unit normally again. If
"CHECK SP WIRE" appears on the display, the speaker
cables may be short-circuited. Make sure bare speaker
wires are not touching each other or the back panel of
the unit, then turn the unit on again. If "NG" is displayed,
immediately unplug the power cord from the wall outlet
and contact your dealer.
• The protective circuit function may have been activated
because the temperature of the unit rose abnormally.
If this happens, then the power will continue to turn off
after you have turned the unit on again. Make sure the
unit has plenty of space for ventilation around it, wait for
the unit to cool down sufficiently, and then try turning it
on again. This is out of your users manual.

General suggestions are to remove all speakers and speaker wiring with unit off. Turn on and see if problem has stopped. If not, let unit cool down if warm and try again later. If problem is still there it needs repair shop work. I fht problem went away, shut off power and connect one speaker at a time and testing. Keep adding speakers one at a time with power off and see if a bad speaker or wire set can be located

Aug 20, 2017 | Onkyo Audio Players & Recorders

1 Answer

Onkyo tx nr656 showing. NR:LCRSLSRBLBR, Any idea. Not working at all.

Hello, I am sorry about your issue. The receiver may have detected a problem with a speaker or speaker wire. Please contact Onkyo at 800-229-1687 option #3 so that we can troubleshoot with you. Thank you, Onkyo USA

May 13, 2017 | Onkyo Audio Players & Recorders

1 Answer

My onkyo tx-nr 616 suddenly stop working, error pls check sp-cable, what could be the reason.

Either voice coil to the speaker is shorted, or the audio output section circuit to your receiver has shorted component/s at it. Disconnect all the speakers from the set, and check whether it shows any warning error like this. If dhows, the fault is within the receiver itself. If does not show any error message, switch off the set, and connect the speakers; one by one at a time, and try to find out which one is faulty. Be remember to switch OFF the power to the receiver, each time when one speaker box is connected. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Oct 26, 2014 | Onkyo Audio Players & Recorders

1 Answer

Onkyo 545 one channel don't work

Oct 09, 2012 | Onkyo TX-SV545 Receiver

1 Answer

My onkyo receiver say protect

If protect is coming up on the display, it means the system is detecting a short somewhere on one of the speakers and so is turning the amp off to avoid damage.
Check all the connections at the back of the amp to ensure they are not shorting, and at the back of each speaker, if nothing is found there, check each wire for damage (like squashed or rodent damage).

Jan 29, 2010 | Onkyo TX-8011 Receiver

1 Answer

Every time I turn on my Onkyo receiver it goes in to protect mode.

Please check your speaker cables. Make sure that all of them are seated properly, none is touching each other or to the body of receiver.

Are you using banana plugs for connecting speaker or just directly. Some times even a little tiny frayed speaker cable touching the receiver could trigger the protect mode. Be careful, since protect mode is sometimes not fast enough to activate and it could blow a few trasistors in the power output circuit.

Please take out all the speaker cables, unplug your receiver from the mains and try to restart without any cables plugged. If it powers on then you are lucky.

If not and the receiver still goes into protect mode or wont turn on then it possible that there are bad connections on the main board or have some blown transistors. How old is your system? if its still under warranty then you should contact Onkyo immidiately.

Let me know if I can be of any further help. Please do rate this solution and thanks for using FixYa!

Mar 08, 2009 | Onkyo TX-SV727 Receiver

1 Answer

I just hooked up my old Onkyo TX-8511 receiver to my bose speakers, which is also hooked up to a subwolfer. When I turn the volume up the system goes into protect mode. Any solutions.

Just check your speaker cabling again. Make sure that all of them are seated properly, none is touching each other or the body of receiver. Rewire if necessary..
Are you using banana plugs for connecting speaker or just directly. Some times even a little tiny wire touching the receiver could trigger the protect mode. Be careful, since protect mode is sometimes not fast enough and it could blown a few trasistors in the power circuit.

Otherwise, do your bose speakers play out load on other systems?

Mar 08, 2009 | Onkyo TX-8511 Receiver

1 Answer

Problem with onkyo tx 919 unit

Hi...
If you've had it "fixed" 3 times and the problem comes back either you have the wrong impedance (ohms) speakers connected or the power supply in the unit is the actual problem.

Happy new years,

Scott

Jan 01, 2009 | Onkyo TX-DS939 Receiver

1 Answer

It says protect on the front screen

An amplifier goes into protect when it detects a load with too low an impedance. If it displays protect with no speakers connected at all, the amplifier is damaged. If not, reconnect speakers one at a time (while the amp is off!) to determine the cause of the fault.

It may be as simple as a single strand of copper wire shorting between the positive and negative terminals of a connection.

:)

Nov 29, 2008 | Onkyo GX-D90 Main / Stereo Speaker

Not finding what you are looking for?

View Most Popular

Audio Players & Recorders

I have a onkyo tx-nr828 that will not power on

Onkyo Audio Players & Recorders

Open Questions:

0 Answers

Ask a Question

Usually answered in minutes!

Latest Celebrity Headphones Report

View all Fixya Reports

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual

Hi! my name is Arthur. I have Onkyo nr 545 . Problem is Det.Protect: I I probaly connect speaker after circuit +and- speaker cabel beetween . Can you help me

1 Answer

Ambrosia Heart

5 Suggested Answers

Anonymous

Anonymous

Anonymous

Mical Caterina

Rommel Cana

Add Your Answer

Attachments: Added items

Related Questions:

I have a onkyo tx-nr828 that will not power on

My onkyo tx-rz810 keeps going toDet.pretction mode how do I get it out of that mode

Onkyo tx nr656 showing. NR:LCRSLSRBLBR, Any idea. Not working at all.

My onkyo tx-nr 616 suddenly stop working, error pls check sp-cable, what could be the reason.

Onkyo 545 one channel don't work

My onkyo receiver say protect

Every time I turn on my Onkyo receiver it goes in to protect mode.

I just hooked up my old Onkyo TX-8511 receiver to my bose speakers, which is also hooked up to a subwolfer. When I turn the volume up the system goes into protect mode. Any solutions.

Problem with onkyo tx 919 unit

It says protect on the front screen

Not finding what you are looking for?

Audio Players & Recorders

I have a onkyo tx-nr828 that will not power on

Open Questions:

Onkyo DX-C390 CD changer won't play on all trays, skips on others

onkyo r30 display not works

ONKYO HT R393 Surround sound channel no sound

Onkyo tx sr-601 stereo reciever : is there an easy way to program it just for FM stereo listening?

Related Topics:

Ask a Question

Popular Questions

Code for Verizon FIOS remote Control

My Onkyo tx-sr606 7.1 receiver turns off by itself

Code for Sony BDP-S300 Blu-ray player on Onkyo remote

How to Hook up HDMI from Comcast Motarola Cable Box

What is error code NG:LCRSLSRBLBR"

Latest Celebrity Headphones Report

Top Onkyo Audio Players & Recorders Experts

Ted28

Grubhead

The Knight

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Manuals & User Guides

Tx-sr702_602_manual_e.pdf....

Onkyo TX-SR502 SR-8250.pdf....

TX-SR304_En_0124.pdf....