Kenmore Dryer Model 110

i don't know. it could be the heating a home fuse or your
dryer's heating element. open the dryer door. locate the dryer fuse or circuit breaker to see if it needs replacing or resetting. reset the breaker a few times or replace fuses with a good one. shut the dryer door and choose a new settings with high heat for a test. if OK, good. if no heat, it may be your heating element or something else. if not able to repair yourself, consider the age of your dryer and
cost of a replacement. if it runs OK and fails again in days
or weeks, your home wiring should be inspected. call for service right away.

http://www.davesrepair.com/DIYhelp/DIYreplacingWPLdryels.htm

Check the following to address this issue.(Most common issue will be a burned out thermal fuse.)




1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Hope this info helps, ps don't forget to give me a rating thanks!!


For an electric dryer that runs but doesn’t heat, follow this repair roadmap:
Flip the circuit breaker off and then back on. Electric dryers run on a two-pole, 240v breaker. A common problem is for one of the legs to break which cuts the 240v that the elements need to heat up but it still supplies the 120v for the motor. The result is that the dryer runs but doesn’t heat.
If the breaker checks out, then it’s time to do some surgery. Unplug the dryer and open it up.
. Use your ohm meter to test the thermostats. All should show continuity.
Measure the resistance of the heating element with your ohm meter. Normal readings are in the neighborhood of 30 ohms.
In rare cases, the centrifugal switch in the motor can fail which breaks the power circuit for the heating elements. If this is the case, then the entire motor must be replaced since the centrifugal switch is built into the motor.

It's almost certainly the heating element, unless you have moved to a home without natural gas from one that did. Then of course, it won't have a source of energy. How can you not know if it's gas or electric?????

If all of the components are reading ok then you need a timer. Touch your 2 leads together. 0 ohms rght. That means you have a complete circuit.If you get the 0 reading then the element must be otay. Bad timer. Take that fancy meater of yours and atttach one of them leads to the timer leg marked RH. Yank the wire off the terminal beore you test. Move the timer around. You should get the famous 0 reading along the way. If you don't then that means you have the bad timer.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Tht means that the element is not heating on.

You need to call a technician to test the element, the thermic sensor, and the control assembly.

The most likely is a defective heating element, that must be replaced.

usually if it heats up but long dry times ,,air flow problem inspect exhaust hose and vent s should resolve problems...

Where is the location of the heating element for a Kenmore 80 series dryer heavy duty model # 77834795

NEED More info ...Need model # and type dryer... info u gave is misleading