Question about Dishwashers

1 Answer

Water will not spray out - Dishwashers

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dishwashers Master
  • 85,206 Answers

Failed pump or control board, test the pump.

Posted on Aug 15, 2019

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spray arms not working


Hi frustrated in Raleigh,
I understand that the spray arms are not moving or spraying water, even after you have cleaned the screens and arms. What might be happening is you are not getting enough water pressure to the dishwasher.
The hot water line to your dishwasher must provide water pressure between 20 and 120 psi.
Low water pressure may occur when laundry or showers are in operation.
Wait until water use is reduced before starting dishwasher.
If you are still noticing that the spray arms are not moving or spraying water, I would have a local Authorized Technician come out to see what exactly is going on with the spray arms of your dishwasher.

-Best Regards-

Jan 06, 2014 | Frigidaire FPHD2491KF Dishwasher

1 Answer

Water sprays into machine on spin cycle


the machine is programmed to spray water during the initial period of the spin cycle as an added method of removing any remaining suds
that stops then the spin cycle goes into high speed spin for that last few minutes
If the problem is that it continues to spray water until the spin cycle is finished it will be the program board or program controller switch

Oct 15, 2017 | Washing Machines

1 Answer

Water spray not working


I got a thin needle and gently made a hole through the centre of the nozzle - where the water would usually come out. That cleaned the scum build up out of it and it's working fine again. My nozzle does seem to look like its going into the iron but perhaps it's to get the correct angle of spray onto the clothes.

Feb 13, 2010 | Sunbeam Irons

1 Answer

My whirlpool Quiet Partner 1 leaks from the bottom of the door.


Some leaking around-under-from the door on dishwashers can be traced back to a split in the spray arm. If the lower spray arm develops a split in it, the spray arm can turn too fast, and shoot water directly at things that it is not suppose to spray water at....sprays water at the door vents or edges and can create water leaks. See if thats the problem

Nov 13, 2009 | Whirlpool 24 in. GU2500 XTP Built-in...

1 Answer

Water is not spraying


Plugged holes in spray bar or plugged filter in bottom, preventing water from draining down to the pump area. If the pump can't get water, it won't pump water up into spray bars. If spray bar holes are plugged, water can't get out.

Nov 05, 2009 | KitchenAid 24 in. KUDS25 Built-in...

1 Answer

Not enough compression to spray thompson water


Maybe just plugged. If it has the nozzle that can be rotated 180 degrees, roll it and try to spray. Sometimes a bit of debris gets in there and stops it up. If no on the rotatable nozzle, take the tip off and try to push liquid back to the container, or a waste bucket, to clear the line. You also may need to clean the tip. One last item.....since you sprayed water.....if you chased the water with the TWS, you may have made an emulsion. If so, remove the spray gun, and turn on the pump, pumping into a waste container, until the emulsion is displaced. Clean the gun. I'd say that if it'll spray water, TWS would be even easier.
Regards, --W/D--

Aug 03, 2009 | Wagner Air Tools & Compressors

1 Answer

Spray is very fine or not spraying


Any air leaks in the suction portion of the machine will cause it not to spray or spray weak. This is a airless paint spray correct? Your paint should be at least thin down using 1 gallon of water for a 5 gallons of paint. I find Baer paint is even thicker and had to slowly add more water.

To check if it is your paint. Fill a bucket of just water and see if it will spray your water. Of course after it gets a good prime. Let it recirculate until the water is coming out of the bypass as a solid stream. If it does not spray water then you have either a air leak or your pump packing needs replacement.

Let me know the results and the make and model of the machine.

Mar 20, 2009 | Binks Air Tools & Compressors

1 Answer

Upper spray arms not spraying water


It sounds like you have a model that has a pot washer cycle that blocks water flow to those arms. What cycles are on your keypad? Sounds like you have it set or single rack wash

Dec 08, 2008 | GE Profile PDW8400J Built-in Dishwasher

1 Answer

Dishwasher spray arms don't spin & spray water


Could be a a couple different issues.. Not filling with enough water or food chopper broke or food chopper filter screen clogged.

Check water level:
Run the DW and wait for the main wash to start (water will fill. pause then complete fill) The water should be no more than 1/4 inch below the heating element. If not there..replace water inlet valve.

Inspect food chopper:
1. Remove lower spray arm and rear water supply tube to upper spray arm.
2. Remove torx screws that secure the sump cover.
3. Remove primary filter
4. Remove food chopper cover to expose the chopper assembly. Inspect for breakage or blockage.

76fcd7c.jpg

If you need further assistance, let me know
Regards,
reg501

Jun 29, 2008 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Dishwasher


Plugged filter or spray arms .

Sep 30, 2017 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18110 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...