Washing Machines Logo

Related Topics:

M
Mihail Georgiev Posted on Jul 03, 2019
Be the first to answer

I have washing machine AEG witch shows an error E23 in service mode.

E23 means that there is an error with the triac of the pump. I checked the main board but the triac is fine. The water is also draining. Any solution to this ?

Answer This Question

5 Related Answers

Anonymous

  • 4 Answers
  • Posted on Jul 08, 2008

SOURCE: error code e60

Hi I had this on my zanussi not long ago I pressed the reset button in for 5 seconds and it stopped . The computer board needed resetting. Hope this helps

Ad

rafiqahmad

  • 1 Answer
  • Posted on Dec 01, 2008

SOURCE: AEG LAVAMAT 74620 - Washing Machine CE error code

Replace Water distributor (Dispenser Drawer) then will be Ok

Rafiq

Anonymous

  • 1 Answer
  • Posted on Mar 20, 2009

SOURCE: whirlpool duet sport wfw8300sw00 f-21 error

Unplug the machine. Unscrew the 3 screws under the front edge of the washer. The service technician manual is attached to the panel that slides down and off. Find F21 code. See suggested procedures. Note: My drain pump filter had a baby wash cloth in it along with some change that was disrupting the flow. It is exceptionally easy to remove, clean, and reinstall. Just line up installation notches when reinstalling. Whirlpool should have mentioned this filter in the User & Care Guide, but I could not find it anywhere in there.

mgprice

Mike Price

  • 744 Answers
  • Posted on Jun 23, 2009

SOURCE: Miele Washing Machine Code: Check drain

This means that the drain attached to the pump is clogged, remove the drain plug check fro debris and replace...you should be good to go.

Anonymous

  • 1 Answer
  • Posted on Mar 13, 2010

SOURCE: Whirlpool washing machine "clean pump" error light.

take top off machine. look down right side and you will see a disc about 50 mm in diameter, attached to this is a small flexible rubber pipe, take this off at the disc and blow through it,( you will need some type of pipe to connect to the rubber pipe).this worked for me with the very same problem.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

AEG Lavamat washing machine shows error code E6H in test mode. Does anyone know what this error code means please?
Error code E6H on your AEG Lavamat washing machine typically indicates a problem with the heating system. It may mean that there is a problem with the heating element, the temperature sensor, or the control board. It's best to refer to the manual for your specific model for the exact meaning of the error code and for further instructions on how to resolve the issue.
If you are unable to resolve the issue yourself, it is recommended that you contact a professional repair service for assistance. Attempting to repair a washing machine can be dangerous and may void your warranty if not done properly.
Read full answer
Feb 12, 2023 • AEG Washing Machines
0helpful
1answer

Hi there, my Smeg WDF12C7-1 washing machine shows up error 11. Please help. Much appreciate.
Smeg washer error code E11 means motor triac short error. The motor control triac is a small component mounted on the controller and is used to switch your motor on and off. Check the mains supply, the main control module and the main drive motor. It is also possible that the part is failing under load and needs replacing.
Read full answer
May 02, 2018 • Smeg Washing Machines
0helpful
1answer

E23 error ? what is it
E23 - Drain pump triac faulty
Could be: Drain pump faulty; wiring faulty; PCB faulty.

Dado
Read full answer
Mar 17, 2016 • Zanussi ZWF1440 Front Load Washer
0helpful
1answer

Showing error 23
E23 - Drain pump triac faulty
Could be: Drain pump faulty; wiring faulty; PCB faulty.

Dado
Read full answer
Mar 17, 2016 • Zanussi ZWF1440 Front Load Washer
0helpful
1answer

I have an Affinity washing machine that shows an E23 error code.

Hello Robert Reische, thank you for your inquiry!

I understand that your Frigidaire washer is showing an "E23" error code. Based off the information I show "E23" stands for drain pump relay on board failed or wire off the pump. Which means you could have an issue within the main control board or wiring to pump. Since it could be any one of these underlying issues I would recommend having a technician come out to properly diagnose and repair your appliance. Hopefully this helps. -Matt

Read full answer
Sep 11, 2014 • Frigidaire ATF6000ES Front Load Washer
0helpful
1answer

How can I correct error code 25 on an AEG OK-LAVAMAT 74640 update washing machine mean?
Family error code "E20" means difficulties in draining, but I never heard for error code E25 on this model. Could be : E21, E23 and E24 error code.

Dado
Read full answer
Aug 24, 2014 • AEG Washing Machines
0helpful
1answer

AEG Lavamat washing machine model 76850, shows a blinking key and makes clicks and after that shows E40. Thanks John
Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.
I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.
E41 - Door open
E42 - Problems of door closure
E43 - Interlock power supply triac faulty
E44 - Door interlock sensing circuit faulty
E45 - Door interlock sensing circuit triac faulty

Possible causes:
Door interlock faulty, wiring faulty or PCB faulty.

24899241-2jugp0yd2m13ocssblsa4goy-3-0.png
Dado
Read full answer
Aug 02, 2014 • AEG Washing Machines
0helpful
2answers

Error c3
http://www.aeg.co.uk/Support/Troubleshooter/?Command=Detail&CatId=98&SymptomId=1412&DetailId=1412shows AEG's meaning for a C3 error code
Read full answer
Feb 06, 2013 • AEG Washing Machines
2helpful
2answers

Showing F01 error code on readout? what does that mean?
Hi.

It depends on the model. On Whirlpool built machines F01 is EEPROM error, pump drive error, or main relays error.

With Hotpoint F01 means defective triac or defective motor.
Read full answer
Aug 18, 2011 • Washing Machines
4helpful
2answers

What does e 62 error code refer to?
E62: Overheating during washing this is real ans now iam giving u more tips abt error -
E11: Difficulty in filling during wash phase
E13: Water leakage.
E21: Difficulties in draining .
E23: Malfunction of drain pump triac.
E24: «sensing» circuit of the component (triac) that controls the drain pump faulty
E33: Incongruence between closure of anti-boiling and 1st level contacts of pressure switch
E35: Water level too high
E36: «sensing» circuit of anti-boiling pressure switch faulty
E37: «sensing» circuit of 1st level pressure switch faulty
E39: "HV" «sensing» circuit of anti-overflow pressure switch faulty
E40: Door open, Interlock, wiring or main PCB
E41: Door open
E41: Problems with aperture of door
E42: Problems with aperture of the door
E42: Problems with aperture of the door
E43: Problems with the triac which actions the door interlock
E43: Problems with the triac which actions the door interlock
E44: Door closure «sensing» circuit faulty
E45: Problems with the «sensing» circuit of the triac that actions the door interlock
E51: Motor power triac short-circuited
E52: No signal from the motor tachymetric genetaror
E52: No signal from the tachymetric generator
Procedure for checking commutator motors
E53: Problems with the «sensing» circuit of the triac which powers the motor
E54: Motor relay contacts sticking
E61: Insufficient heating during washing
E62: Overheating during washing
E66: The contacts of the heating element power relay are always closed
E71: NTC washing sensor faulty.
E82: Error in reading the RESET/OFF position of the programme selector.
E83: Error in reading the programme selector code
E93: Incorrect machine configuration.
E94: Incorrect configuration of washing cycle
E95: Communications error between microprocessor and the EEPROM
E96: Incongruence between control panel version and configuration data
E97: Incongruence between selector version and configuration data
EA1: Drum positioning system (DSP) faulty (top-loaders only)
EB1: Incorrect mains frequency
EB2: Mains voltage too high
EB3: Mains voltage too low

E32 INCORRECT CALIBRATION OF ANALOGIC (ELECTRONIC) PRESSURE SWITCH. IF THE MACHINE IS DRAINING OK, THEN IT IS THE SWITCH
E32 relates to the electronic pressure switch, normal pressure switch,inlet valves,poor water mains pressure and finally the main control board
E90 means theres a fault on the main control module so A;will need a new control module or B; get an engineer to try re-configureing the module
Read full answer
May 16, 2011 • Hoover Washing Machines
Not finding what you are looking for?

View Most Popular

Washing Machines

Related Question

AEG Lavamat washing machine shows error code E6H in test mode. Does anyone know what this error code means please?

  • AEG Washing Machines

581 views

Ask a Question

Usually answered in minutes!

Popular Questions

AEG washing machine error code

AEG Lavamat 74640 Front Load Washer

How do i re set an EFO code on an AEG LAVAMAT

AEG Lavamat 74640 Front Load Washer

Drum has dropped/is not aligned with opening.

AEG Lavamat 74640 Front Load Washer

Aeg lavamat error code E20.

AEG Washing Machines

AEG Lavamat error E 20? what I have to do?

AEG Lavamat W1450 Front Load Washer

Top AEG Washing Machines Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

john h

Level 3 Expert

29494 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Lavatherm_t35850.pdf....

AEG T35850 Euro...

PDF Manual
D3566154-aae0-4a72-9a1a-27da6baf9f6e[1...

AEG Lavamat 72640...

PDF Manual
D3566154-aae0-4a72-9a1a-27da6baf9f6e[1...

AEG Lavamat W1050...

Loading...