Washing Machines Logo

Related Topics:

C
Chris Barber Posted on Jun 01, 2019
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

My whirlpool cabrio has begun to stop with the 'wash' light on but the clothes are barely wet and certainly not washed.

Ive tried to reset using the online trick with tunring the knob clockwise and anti-clockwise but it hasn't worked.

1 Answer

keith jones

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Master:

An expert who has achieved Level 3.

  • Whirlpool Master 747 Answers
  • Posted on Jun 02, 2019
keith jones
Whirlpool Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Master:

An expert who has achieved Level 3.

Joined: Apr 09, 2016
Answers
747
Questions
3
Helped
314481
Points
1478

Check there is plenty of water going into the machine if not probably a faulty water solenoid

5 Related Answers

Anonymous

  • 5158 Answers
  • Posted on Jan 24, 2009

SOURCE: Our 2000 VW Cabrio wont

get a can of WD40 and coat everything with it... don't be that sparse with it. keep in mind oil does not conduct electricity but it will repel the water.

Robert

Ad

Anonymous

  • 15 Answers
  • Posted on Feb 09, 2009

SOURCE: Electric mirrors not working

Hi,

Try check the fuses. If they are ok, then try checking the switch panel, it might have accumulated some water or liquid that you used which later caused some short circuit or corroded the terminals, Meaning there is no complete circuit for the mirrors.

Anonymous

  • 6 Answers
  • Posted on Aug 29, 2009

SOURCE: 2002 eclipse rs with wet floor

Pull up the carpet and see if the rubber plug in the bottom of the floor pan is in their or in their tightly (should not be loose) unless it is coming up higher from the firewall

A

Anonymous

  • Posted on Sep 25, 2010

SOURCE: i just replaced a rear wheel bearing. Now the ABS

Either drive it until it has gone thru several drive cycles,could take days, or use a code reader or scanner,and see if that works

Anonymous

  • 645 Answers
  • Posted on Oct 08, 2010

SOURCE: right floor wet but not

It sounds like yourdrain hole for your ac evaporator is clogged and needs to be unclogged. This can be done by taking it to a shop and have them blow out the drain hole with a air gun. They may not even charge you if so it should not be much.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Whirlpool Cabrio WTW6700TW1 skips wash cycle and stops after 14 minutes to oL

oL is an Overload error. Try running a cycle empty.

If oL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent. Close lid and press START/PAUSE.

oL - Error Code - Washer - Product Help ' Whirlpool

https://www.google.com/search?q=whirlpool+cabrio+ol+error

..
0helpful
2answers

Whirlpool Cabrio Washer does not spin the water completly out of the clothes

probably not getting into high speed spin mode
they spin slow in the initial stages to allow the clothes to become evenly distributed then after the water is removed they pick up speed
It is possible a problem in the program board not advancing to high speed
Call in a technician for a proper diagnosis and a quote
0helpful
1answer

Whirlpool cabrio washwer wtw5600xw0 washes fine but when it's time to drain ,it drain's some of the water and it stops i had the pump checked and thought it was bad but it was not , i had a local repair...

So when you say it's not pumping all water out, is there still water standing in tub or no water standing and clothes are just sopping wet? Is machine spinning? If not spinning, could be actuator that shifts transmission from agitate to spin.
0helpful
1answer

Cabrio washer stops spinning and doesn't restart

it sounds like the water pump is not emptying properly, blow down the water outlet pipe to see if is clear if not go to the water pump and clean it out there is probably a button , paper clip or other debris preventing it from doing its job eric
0helpful
1answer

Why doesn't Cabrio washer wash the clothes?

This model has gone through different control board revisions, could be control board related, service mode would have to be accessed to have machine run thru self-diagnostics. if it does not agitate on self-diag mode, unit needs board
0helpful
1answer

I have a whirlpool cabrio washing machine. I have a problem. Our clothes are coming out smelling musty and nasty. They dont start smelling until they are wet, like with sweat Or the towels when we dry off...

If you dont wash whites with clorine bleach, you may want to every once in a while. Clorine kills germs and backteria which can smell. washer pumps do not get 100% of the water out.
0helpful
2answers

Have a Whirlpool Cabrio top loader washing machine, keep getting code F1 during beginning of cycle. Got code uL for the first time today. What do these codes mean.

Have a Whirlpool Cabrio top loader washing machine, keep getting UL code when spin on high speed and the machine bangs all over the place.. Model num wtw6300sw0 Type 581


  • processing_throbber2.gif
0helpful
1answer

Clothes come out with lint all over. i have to use a lint roller on my clothes.

Check the pockets of pants and make sure there is nothing in them ....Take a damp cloth and wipe out the inside of the drum to try to get excess lint out of it.... also run a short wash with no clothes in washer to see if it cleans the washer out certain clothes such as towels should also be washed by themselves ...........
7helpful
1answer

Whirlpool cabrio washer keeps flashing code F50

The F50 error code indicates that the RPS (rotor position sensor) detects no motor rotation. Check to see if the basket spins freely. If not, you could have an item caught between the outer tub and the inner spin basket. A toy or other item underneath the washer could also prevent the basket from spinning and would result in this F50 code.

If the basket spins freely, you could have a wiring failure that would prevent the motor from spinning.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question$$$$
Not finding what you are looking for?

76 views

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...